HP CC487-91209 Fax Manual Download Page 88

Page: 88 / 168

●

General Settings

●

Date/Time Settings

●

Date/Time

Touch the correct

Time Zone

setting for your locale.

Touch the

Month

drop down menu and select a month.

Touch the boxes next to the

Date

drop down menu to enter the day and year from the keypad.

Touch the boxes below the

Time

heading to enter the hour and minutes from the keypad and

then touch the

button.

Touch the

Adjust for Daylight Savings

feature, if necessary.

Touch the

Save

button to save the settings.

Set or verify the date/time format

The date and time format setting for the fax accessory is in the same format as the product date and

time setting. This information can be entered using the Fax Setup Wizard, or by following these steps:

From the Home screen, scroll to and touch the

Administration

button.

Open the following menus:

●

General Settings

●

Date/Time Settings

●

Date/Time Format

Touch a

Date Format

option.

Touch a

Time Format

option.

Touch the

Save

button to save the settings.

76 Chapter 3 HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 88 / 168

Search results

Summary of Contents for CC487-91209

Reviews: