manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 151 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 151

Declaration of conformity

Declaration of Conformity

according to ISO/IEC 17050-1 and EN 17050-1: DoC# BOISB-0703-00-rel.12.0

Manufacturer's Name:

Hewlett-Packard Company

Manufacturer's Address:

11311 Chinden Boulevard

Boise, Idaho 83714-1021, USA

declares, that the product

Product Name:

HP Analog Fax Accessory 500

Regulatory Model Number:

2)

BOISB-0703-00

Product Options

All

Toner Cartridge/Image Drum

N/A

conforms to the following Product Specifications:

SAFETY:

IEC 60950-1:2005 / EN60950-1: 2006 +A11:2009 +A12:2011

EMC:

CISPR22:2005 + A1/ EN55022:2006 + A1- Class A

1),3)

EN 55024:1998 +A1:2001 +A2:2003

EN61000-3-2:2006 +A1:2009 + A2:2009

FCC Title 47 CFR, Part 15 Class A

1)

 / ICES-003, Issue 4

TELECOM:

ES203-201; FCC Title 47 CFR, Part 68

4)

RoHOS

EN 50581:2012

Supplementary Information:

The product herewith complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC, the
R&TTE Directive 1999/5/EC and carries the CE-Marking 

 accordingly.

This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.

2) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product

name or the product number(s).

3) The product meets the requirements of EN55022 & CNS13438 Class A in which case the following applies: “Warning: This is a class A

product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate

measures.”

4) Telecom approvals and standards appropriate for the target countries/regions have been applied to this product, in addition to those

listed above.

Boise, Idaho 83714-1021, USA

February 2013

For Regulatory Topics only, contact:

ENWW

Declaration of conformity 139

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments