manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 154 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 154

Additional FCC statement for telecom products (US)

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.

On the back of this equipment is a label that contains, among other information, a product identifier in

the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone

company.

The REN is used to determine the quantity of devices, which may be connected to the telephone line.

Excessive RENs on the telephone line may result in the devices not ringing in response to an

incoming call. In most, but not all, areas, the sum of the RENs should not exceed five (5.0). To be

certain of the number of devices that may be connected to the line, as determined by the total RENs,

contact the telephone company to determine the maximum REN for the calling area.

This equipment uses the following USOC jacks: RJ11C.

An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment

is designed to be connected to the telephone network or premises wiring using a compatible modular

jack, which is Part 68 compliant. This equipment cannot be used on telephone company-provided

coin service. Connection to Party Line Service is subject to state tariffs.

If this equipment causes harm to the telephone network, the telephone company will notify you in

advance that temporary discontinuance of service may be required. If advance notice is not practical,

the telephone company will notify the customer as soon as possible. Also, you will be advised of your

right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that

could affect the operation of the equipment. If this happens, the telephone company will provide

advance notice in order for you to make the necessary modifications in order to maintain

uninterrupted service.

If trouble is experienced with this equipment, please see the numbers in this manual for repair and

(or) warranty information. If the trouble is causing harm to the telephone network, the telephone

company may request you remove the equipment from the network until the problem is resolved.

The customer can do the following repairs: Replace any original equipment that came with the device.

This includes the print cartridge, the supports for trays and bins, the power cord, and the telephone

cord. It is recommended that the customer install an AC surge arrestor in the AC outlet to which this

device is connected. This is to avoid damage to the equipment caused by local lightning strikes and

other electrical surges.

Japan Telecom Mark

A08-0138004

142 Appendix C   Regulatory information

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments