HP CC487-91209 Fax Manual Download Page 20

Page: 20 / 168

If necessary, remove the label that covers the fax port on the formatter.

Remove the fax accessory from its packaging.

CAUTION:

The formatter board and the fax accessory card contain parts that are sensitive to

electrostatic discharge (ESD). When handling the formatter board or the fax accessory card, use

static protection such as the following: 1) a grounding wrist strap that is connected to the metal

frame of the product. 2) Hold the metal frame of the formatter in your hand.

Avoid touching components on the formatter board or the fax accessory card.

Locate the fax-accessory support on the formatter, and unwind the fax wiring harness from the

support. Do not disconnect the fax wiring harness from the formatter. Place the fax accessory

into the support. Press down so the fax-accessory is securely seated in the support. Verify that

the telephone connector on the fax accessory aligns with the opening on the metal frame of the

formatter.

Chapter 2 HP Color LaserJet CM3530 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 20 / 168

Search results

Summary of Contents for CC487-91209

Reviews: