HP CC487-91209 Fax Manual Download Page 116

Page: 116 / 168

Status message bar

While sending and receiving faxes, status information will display in the status bar located at the top

of some touch screens. This status includes such information as: Ready, Receiving call, Page sent,

and others.

Send a fax

To send a fax, you can use one of three basic methods to enter numbers:

●

Enter numbers manually.

●

Enter numbers using speed dial.

●

Enter numbers using the fax address book.

NOTE:

For online information about sending a fax, touch

on the screen to access the help menu,

and then touch the

Fax

menu under the list of help topics.

Allowable characters in fax numbers

●

Digits (0–9)

●

spaces

●

[]

●

()

●

–

●

When entering a phone number from the numeric keypad, use the Pause button include any pauses

or other numbers, such as area codes, access codes for numbers outside a PBX system (usually a 9

104 Chapter 3 HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 116 / 168

Search results

Summary of Contents for CC487-91209

Reviews: