manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 32 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 32

Set the JBIG compression mode

Enabling JBIG compression can reduce phone-call charges by reducing fax transmission time and is,

therefore, the preferred setting for shorter faxing times. However, JBIG might cause compatibility

problems when communicating with some older fax machines, in which case you might need to

disable it.

NOTE:

JBIG compression only works when both the sending and receiving machines have JBIG

compression.

To enable or disable JBIG compression, perform the following steps.

1.

On the control panel, scroll to and touch the 

Administration

 icon to open the Administration

menu.

2.

Scroll to and touch 

Initial Setup

.

3.

Scroll to and touch 

Fax Setup

.

4.

Scroll to and touch 

Fax Send Settings

.

5.

Touch 

JBIG Compression

 to see the settings.

6.

Touch 

Enabled

 (default) to enable JBIG compression, or touch 

Disabled

 to disable JBIG

compression.

Change the sharpness setting

The Sharpness setting specifies the sharpness that the scanner uses when the product scans your

original. Sharpness enhances the edges of the original so that faint or fine text and graphics are

reproduced more sharply. Increasing sharpness increases resolution which also increases

transmission time.

1.

On the control panel, touch the 

Fax

 icon to display the Fax screen.

2.

Scroll to and touch 

More Options

.

3.

Scroll to and touch 

Image Adjustment

.

4.

Under the 

Sharpness

 heading, touch the left arrow to decrease the sharpness or touch the right

arrow to increase the sharpness of the image.

5.

Touch 

OK

 to accept the setting.

Change the background setting

If you are faxing a document that is printed on colored paper, you can enhance your fax copy quality

by removing the background that might cause your fax copy to streak or blur. Removing the

background increases resolution which also increases transmission time.

1.

On the control panel, touch the 

Fax

 icon to display the Fax screen.

2.

Scroll to and touch 

More Options

.

3.

Scroll to and touch 

Image Adjustment

.

4.

Under the 

Background Cleanup

 heading, touch the left arrow or touch the right arrow to change

the background setting.

5.

Touch 

OK

 to accept the setting.

20 Chapter 2   HP Color LaserJet CM3530 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments