manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 146 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 146

Fax accessory product specifications

 

Environmental specifications

Operating environment

●

Temperature: 10 to 32.5° C (50 to 91° F)

●

Relative Humidity: 20 to 80 percent (no condensation)

Storage environment

●

Temperature: -20° C to 40° C (-4° F to 104° F)

●

Relative Humidity: Less than 95 percent (no

condensation)

Fax specifications

 

Fax compatibility

●

CCIT/ITU-T Group 3, EIA/TIA Class 1, Class 2.1

Phone connector

●

RJ11

Compression methods

●

MH, MR, MMR, and JBIG

Transmission speeds and standards supported

●

V.17 at 14,400, 12,000, 9,600, 7,200 bps

●

V.33 at 14,400, 12,000 bps

●

V.29 at 9,600, 7,200 bps

●

V.27 at 4,800, 2,400 bps

●

V.34 at 16,800, 19,200, 21,600, 24,000, 26,400, 28,800,

31,200, 33,600 bps

Modem speed

●

Up to 33.6K bits per second (bps)

Speed dialing

●

Yes

Fax resolution, (send and receive)

●

Standard - 200 x 100 dots per inch (dpi)

●

Fine - 200 x 200 dpi

●

Superfine - 300 x 300 dpi

●

Ultrafine - 200 x 400 (receive only)

●

Ultrafine - 400 x 400 (receive only)

134 Appendix B   Specifications

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments