manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 24 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 24

●

Country/region

●

Fax phone number

●

Company name

This information is used in the fax header, which is printed on all outgoing faxes.

The wizard starts when the product is first turned on. You can choose to use the wizard or exit the

wizard to configure the settings at a later date.

You can also access the wizard through the 

Administration

 menu on the control panel. Touch the

Initial Setup

 menu, and then touch the 

Fax Setup

 menu.

NOTE:

The settings configured using the wizard on the control panel override any settings made in

the embedded Web server.

Fax setup menu

Set the required fax settings by accessing the 

Administration

 menu on the control panel. Touch the

Initial Setup

 menu, and then touch the 

Fax Setup

 menu.

NOTE:

If the 

Fax Setup

 menu settings does not appear in the menu listing, LAN fax might be

enabled. When LAN fax is enabled, the analog fax accessory is disabled and the fax menu does not

display. Only one fax feature, either LAN fax or analog fax, can be enabled at a time. The fax icon

displays for either fax feature. If you wish to use analog fax when LAN fax is enabled, use the

HP MFP Digital Sending Software Configuration Utility to disable LAN fax.

Set or verify the date and time

The date and time setting for the fax accessory is the same value as the product date and time

setting. If this is the first time you are turning on the product, you are prompted for this information.

To verify or change the date and time settings, complete the following steps.

1.

On the control panel, scroll to and touch the 

Administration

 icon to open the Administration

menu.

2.

Scroll to and touch 

Initial Setup

 to display the setup settings menu and then touch 

Fax Setup

.

3.

Touch 

Required Settings

.

4.

Select the date format and then enter the date.

5.

Select the time format and then enter the time.

6.

Touch 

Save

 to accept the settings.

Set, verify, or change the country/region

The country/region setting identifies the country/region where the product or fax accessory is located.

This setting also sets the date and time format and minimum and maximum rings-to-answer range for

the country/region. Because this setting is a legal requirement in some countries/regions, it must be

set for the fax accessory to operate. If this is the first time you are turning on the product, you are

prompted for this information.

12 Chapter 2   HP Color LaserJet CM3530 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments