HP CC487-91209 Fax Manual Download Page 130

Page: 130 / 168

Damaged / Enabled/Disabled

Fax accessory has failed; reseat the fax accessory card and

check for bent pins. If the status is still DAMAGED, replace

the analog-fax accessory card.

ENABLED indicates that the analog fax accessory is enabled, turned on; DISABLED indicates that LAN fax is enabled

(analog fax is turned off).

Fax feature is not operating

The fax accessory is installed but the icon does not appear on the product main screen.

Cause

Solution

HP MFP Digital Sending Software Configuration utility has

disabled the analog-fax feature.

Use the HP MFP Digital Sending Software Configuration

utility to enable the analog-fax feature.

The accessory is not operating correctly.

Check the fax accessory status. If the status is

NON-OPERATIONAL, new firmware might need to be

installed.

If the status is DAMAGED and you just installed the card, try

reseating the card and check for bent pins.

If the status is DAMAGED and the card is installed correctly,

the card might need to be replaced.

Faulty formatter board.

Contact your HP service representative for service.

The product is not displaying the fax menus.

Cause

Solution

LAN fax is enabled.

This is normal operation. When the HP Digital Sending

Software enables LAN fax, the analog fax is disabled and the

fax menu, which is used for the analog fax only, does not

open.

General fax problems

Problem

Cause

Solution

Fax failed to send.

JBIG is enabled and receiving fax does

not have JBIG capability.

Set JBIG off.

An "Out of Memory" status message

appears on the status message bar.

The product storage disk is full.

Delete some files from the disk, see the

product user guide for information about

managing the disk.

Print quality of a photo is poor or prints

as a gray box.

Wrong Page Content mode setting.

Try setting the

Optimize Text/Picture

option to

Photograph

Pressed the Cancel button on the

product keyboard to cancel a fax

transmission and the fax was still sent.

Cancellation takes place after making a

selection in the cancellation menu

(displayed after pressing red

Stop

button) and acknowledging with

Cancel faxes using the fax menu.

118 Chapter 3 HP Color LaserJet CM 4540 MFP Series, HP Color LaserJet Enterprise M4555 MFP

Series, HP LaserJet Enterprise 500 MFP Series, HP LaserJet Enterprise 500 Color MFP Series,

and HP LaserJet Enterprise M725 MFP Series

ENWW

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 130 / 168

Search results

Summary of Contents for CC487-91209

Reviews: