HP CC487-91209 Fax Manual Download Page 4

Page: 4 / 168

Development Company, L.P.

Reproduction, adaptation, or translation

without prior written permission is

prohibited, except as allowed under the

The information contained herein is subject

to change without notice.

The only warranties for HP products and

services are set forth in the express

warranty statements accompanying such

products and services. Nothing herein

should be construed as constituting an

additional warranty. HP shall not be liable

for technical or editorial errors or omissions

contained herein.

Edition 1, 5/2013

Part number: CC487-9120

Trademark Credits

Microsoft®, Windows®, Windows® XP, and

Windows Vista® are U.S. registered

trademarks of Microsoft Corporation.

All products mentioned herein may be

trademarks of their respective companies.

Local country/region laws may prohibit the

use of this product outside of the countries/

regions specified. It is strictly forbidden by

law in most countries/regions to connect

nonapproved telecommunications

equipment (fax machines) to public

telephone networks.

ENERGY STAR

and the ENERGY STAR

mark are registered U.S. marks.

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 4 / 168

Search results

Summary of Contents for CC487-91209

Reviews: