manualshive.com logo in svg

HP CC487-91209, Fax Manual, Page: 91 / 168

Share
Download
HP CC487-91209 Fax Manual Download Page 91

Fax settings

The following sections detail the various settings for sending and receiving faxes.

●

Send fax settings

●

Receive fax settings

●

Fax archive and forwarding

●

Polling

Send fax settings

Use the Fax Send Setup menu to configure the following features:

●

Fax dialing settings

●

General fax send settings

●

Default job options

●

Billing codes

Fax dialing settings

Set the fax dial volume

Use the 

Fax Dial Volume

 setting to control the product's dialing volume level when sending faxes.

1.

From the Home screen, scroll to and touch the 

Administration

 button.

2.

Open the following menus:

●

Fax Settings

●

Fax Send Settings

●

Fax Send Setup

●

Fax Dialing Settings

3.

Touch the 

Fax Dial Volume

 drop-down menu and select one of the following settings:

●

Off

●

Low

 (default)

●

High

4.

Touch the 

Save

 button to save the fax volume setting.

Set the dialing mode

The dialing mode setting sets the type of dialing that is used: either tone (touch-tone phones) or pulse

(rotary-dial phones).

To set the dialing mode, perform the following steps.

ENWW

Fax settings 79

Summary of Contents for CC487-91209









































































































































































Reviews:

No comments