HP CC487-91209 Fax Manual Download Page 65

Page: 65 / 168

Scroll to and touch

Billing Codes Report

Touch

to print the report.

Clear the fax activity log and billing code report

The fax activity log and the billing code report use the same database. This setting clears the

database and therefore clears both the activity log and the billing report data.

To clear the fax database, complete the following steps.

On the control panel, touch the

Administration

icon to open the Fax menu.

Scroll to and touch

Resets

to open the menu.

Scroll to and touch

Clear fax activity log

Touch

Yes

to clear all entries, or touch

to exit and retain the entries.

Print the blocked fax list report

On the control panel, scroll to and touch the

Administration

icon to open the Administration

menu.

Scroll to and touch

Information

Scroll to and touch

Fax Reports

Touch

Blocked Fax List

to print the report.

Print the speed dial list report

A speed dial list report lists the fax numbers assigned to speed dial names.

On the control panel, scroll to and touch the

Administration

icon to open the Administration

menu.

Scroll to and touch

Information

Scroll to and touch

Fax Reports

Touch

Speed Dial List

to print the report.

Service settings

These items in the control-panel menus can help with troubleshooting if the corrective action taken

under the Error Codes section is unsuccessful. They are intended to be used when an HP service

representative is assisting you.

Settings in the Initial Setup menu

Open the

Administration

menu, and then select the

Initial Setup

menu. Open the

Fax Setup

menu.

ENWW

Solve fax problems 53

Summary of Contents for CC487-91209









































































































































































Search results

Summary of Contents for CC487-91209

Reviews:

HP CC487-91209, Fax Manual, Page: 65 / 168

Search results

Summary of Contents for CC487-91209

Reviews: