GE Multilin
F60 Feeder Protection System
H-3
APPENDIX H
H.1 CHANGE NOTES
H
Table H–4: MAJOR UPDATES FOR F60 MANUAL REVISION AA2
PAGE
(AA1)
PAGE
(AA2)
CHANGE
DESCRIPTION
---
---
Update
General revision throughout document
---
---
Add
Added 87G restricted ground fault functionality throughout document, including feature table,
specifications, settings, FlexLogic table, and Modbus memory map. Not added to single line
diagram.
---
---
Update
Updated references to digital inputs/outputs to contact inputs/outputs for consistency
5-23
5-23
Add
Added Syslog Format section
5-31
5-31
Add
Added Far-End Fault Indication (FEFI) section
B-
B-
Update
Updated Modbus memory map and F codes
H-8
H-8
Update
Updated product warranty from 24 months to 10 years
Table H–5: MAJOR UPDATES FOR F60 MANUAL REVISION AA1
PAGE
(Z1)
PAGE
(AA1)
CHANGE
DESCRIPTION
---
---
Add
Added content for IEC 60870-5-103 throughout document
2-
2-
Update
Updated order codes
2-
2-
Update
Updated specifications
5-117
5-117
Update
Updated hysteresis numbers and logic diagrams in section 5.4.7 Phasor Measurement Unit
5-175
5-175
Update
Updated Neutral Directional Overcurrent settings to include Dual-V and Dual-I settings to reflect
enhanced polarity criteria
8-
---
Delete
Deleted chapter 8 on security, moving content to other chapters
---
10-
Add
Added Maintenance chapter, moving content from other chapters and adding new instructions to
replace the battery
---
D-
Add
Added new appendix on IEC 60870-5-103 interoperability
Table H–6: MAJOR UPDATES FOR F60 MANUAL REVISION Z1
PAGE
(Y3)
PAGE
(Z1)
CHANGE
DESCRIPTION
---
---
Add
Added CPU options U and V to order code tables in chapter 2, a note above Rear Terminal View
figure in chapter 3, and CPU Module Communications Wiring figure in chapter 3
---
---
Add
Added Parallel Redundancy Protocol (PRP) to order code tables and specifications in chapter 2,
section 5.2.5d Settings > Product Setup > Communications > Network, section 6.3.1 Actual
Values > Status > PRP, and Appendix B Modbus table and F627 and F628 enumeration tables
1-1
1-1
Add
Added General Cautions and Warnings to section 1.1.1
1-5
1-5
Update
Revised section 1.3.1 on system requirements, including addition of support for Windows 7 and
Windows Server 2008
2-10
2-10
Update
Updated several specifications
5-24
5-24
Add
Added section 5.2.5e Routing
5-91
5-91
Update
Updated Figures 5-25 and 5-26 Dual Breaker Control Scheme Logic, sheets 1 and 2
5-95
5-95
Update
Updated Figure 5-27 Disconnect Switch Scheme Logic
5-263
5-263
Add
Reinserted section 5.8.5c Remote Devices: ID of Device for Receiving GSSE/GOOSE Messages,
meaning the Settings > Input/Outputs > Remote Devices settings
Summary of Contents for F60
