configure wireless country-code
ExtremeWare 7.7 Command Reference Guide
1307
configure wireless country-code
configure wireless country-code <code>
Description
Configures the country identifier for the switch.
Syntax Description
Default
Extreme_default
Usage Guidelines
When the Summit 300 is set to factory defaults, you must configure the correct country code using the
country code properties listed in the following table. The country code feature allows you to configure
the approved 802.11a or 802.11b/g “channels” applicable to each of the supported countries.
Extreme Networks ships the Summit 300 to be programmed with Extreme Network's special
extreme_default
country code, which brings up only the B/G radio in channel 6, and turns off the A
radio. When an Altitude 300 wireless port is connected and the Summit 300 is unable to determine the
country for which the Altitude is programmed, then the
extreme_default
country code is used. You
must program the country code on the Summit 300 to enable the remaining channels for the desired
country.
The Altitude 300 wireless port is shipped with a pre-programmed code for the following countries:
•
North America (United States, Canada, Hong Kong)
•
Japan
•
European Union and the Rest of the World.
If you do not program the country code in the Summit 300, then the switch inherits the country code of
the first Altitude 300 wireless port that connects to it, if the Altitude is not programmed for the
'European Union and the Rest of World.
If there is a mismatch between the country codes between the Altitude 300 wireless port and the code
programmed on the Summit 300, the Altitude 300 wireless port is not allowed to come up.
code
Sets the country identifier for the switch.
Australia
Austria
Belgium
Canada
China
Denmark
extreme_default
Finland
France
Germany
Greece
Hong_Kong
Iceland
Ireland
Italy
Japan
Korea_Republic
Liechtenstein
Luxembourg
Mexico
Netherlands
Norway
Portugal
Spain
Sweden
Switzerland
Taiwan
Thailand
UK
USA
Summary of Contents for ExtremeWare 7.7
