Canon iR3245, Service Manual

Page: 473 / 746

Chapter 16
16-5
16.1.5 E500 to E5F9 (Finisher)
0019-7881
iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
T-16-5
Code Detail code Name Detection Remedy
E500 0001 fault in
communication
with the finisher
(common among
all finishers) Replace the finisher controller PCB. Replace
the DC controller PCB.
E503 0002 fault in
communication
with the finisher
(External
finisher) fault in communication between finisher and saddle unit Replace the finisher controller PCB. Replace
the saddle controller PCB. Check the cable.
0003 fault in communication between finisher and punch unit Replace the finisher controller PCB. Replace
the punch drive PCB. Check the cable.
E505 0001 fault in the
backup memory
of the finisher
(common among
all finishers) fault in the data stored in backup memory Turn off the main power. Check the wiring
of the DC controller PCB and the finisher
controller, and check the fuse of the 24-V
power supply. Thereafter, turn the main
power back on.
0002 fault in the EEPROM data of the punch unit Replace the punch driver PCB. Replace the
finisher controller PCB.
E514 0001 fault in stack
delivery motor
(Finisher-S1) When the stack retaining spacer is returned to home position, the belt escape
home position sensor does not go on within 1.5 sec. Replace the finisher controller PCB. Replace
the stack delivery motor. Check the stack
delivery drive mechanism.
0002 When the stack retaining spacer is shifted from home position, the belt escape
home position sensor does not go off within 1.5 sec.
E514 0001 fault in trailing
edge assist motor
(External
finisher) The home position sensor does not go off even when the trailing edge assist
motor has rotated for a specific period of time. Replace the finisher control PCB. Replace
the trailing edge assist motor.
0002 The home position sensor does not go on even after the trailing edge assist
motor has rotated for a specific period of time.
E519 0001 Gear change
motor error
(External
finisher) The home position sensor does not go off even when the gear change motor
has rotated for a specific period of time. Replace the finisher controller PCB. Replace
the gear change motor. Check the gear
change mechanism.
0002 The home position sensor does not go on even when the gear change motor
has rotated for a specific period of time.
E520 0001 The offset motor
or the finisher
controller PCB is
faulty. The offset
home position
sensor is faulty
(Finisher-S1). While the offset motor is in operation, drive was applied for 1000 msec for
movement toward the home position sensor; however, the offset home
position sensor does not go on. Replace the offset motor. Replace the offset
home position sensor. Replace the finisher
controller PCB.
0002 While the offset motor is in operation, drive was applied for 1000 msec for
movement away from the home position sensor; however, the offset home
position sensor does not go off.
E530 8001 Rear alignment
error (Finisher-
S1) The home position sensor does not go on within 2000 msec after the start of
operation when the rear aligning plate is shifted to home position. Replace the finisher controlled PCB.
Replace the rear alignment motor. Check the
rear aligning plate drive mechanism. Check
the rear alignment home position sensor.
8002 The home position sensor does not go off within 1000 msec after the start of
operation when the rear aligning plate is shifted from home position.
E530 0001 Front alignment
error (External
finisher) The home position sensor does not go off even when the front alignment
motor has been rotated for a specific period of time. Replace the finisher controller PCB. Replace
the front alignment motor. Check the front
aligning plate drive mechanism. Check the
front alignment home position sensor.
0002 The home position sensor does not go on even when the front alignment
motor has been rotated for a specific period of time.
E531 8001 Stapler error
(Finisher-S1) At time of staple jam recovery, the home position sensor does not go on with
500 msec after the start of reverse rotation of the stapler motor. Replace the finisher controller PCB. Replace
the stapler. Check the harness.
8002 The home position sensor does not go off within 500 msec after the stapler
motor has been started.
E531 0001 Stapler error
(External
finisher) The home position sensor does not go off even when the stapler motor has
rotated for a specific period of time. Replace the finisher controller PCB. Replace
the stapler. Check the harness.
0002 The home position sensor does not go on even when the stapler motor has
rotated for a specific period of time.
E532 8001 Stapler shift error
(Finisher-S1) The stapler slide home position sensor does not go on within 11 sec when the
stapler is shifted to home position. Replace the finisher controller PCB. Replace
the stapler shift motor. Check the stapler
shift home position sensor. Check the
harness.
8002 The stapler slide home position sensor does not go off within 1.0 sec when the
stapler is shifted from home position.
E532 0001 Stapler shift error
(External
finisher) The home position sensor does not go off even after the stapler shift motor has
rotated for a specific period of time. Replace the finisher controller PCB. Replace
the stapler shift motor. Check the stapler
shift home position sensor. Check the
harness.
0002 The home position sensor does not go on even when the stapler shift motor
has rotated for a specific period of time.
E535 0001 Swing cam error
(Finisher-S1) The home position sensor does not go off within 1000 msec after the start of
operation when the swing arm is shifted from home position. Replace the finisher controller PCB. Replace
the swing cam motor. Check the swing cam
home position sensor. Check the harness.
0002 The home position sensor does not go off within 1.0 sec when the stack
delivery roller swing arm is moved from home position.
E535 0001 Swing cam error
(External
finisher) The home position sensor does not go off even when the swing motor has
rotated for a specific period of time. Replace the finisher controller PCB. Replace
the swing cam motor. Check the swing cam
home position sensor. Check the harness.
0002 The home position sensor does not go on even when the swing motor has
rotated for a specific period of time.
E537 8001 Front alignment
error (Finisher-
S1) The home position sensor does not go on within 2.0 sec when the front
aligning plate is moved to home position. Replace the finisher controller PCB. Replace
the front alignment motor. Check the front
aligning plate drive mechanism. Check the
front alignment home position sensor.
8002 The home position sensor dos not go off within 1.0 sec when the front
aligning plate is shifted from home position.