Canon iR3245, Service Manual

Page: 480 / 746

Chapter 16
16-12
0032 Error in communication after card reader (serial) startup
Communication with the card reader is available at startup, and then becomes
unavailable.
Check the connection of the cable for the card reader (connector disconnected,
cable cut); thereafter, reset the condition in service mode: COPIER >
FUNCTION > CLEAR > ERR.
E730 There is a PDL software error.
1001 An initialization error has occurred. 1. Execute PDL resetting.
2. Turn on the power once again.
100A An error that may be critical to the system (e.g., failed initialization) has
occurred.
1. Execute PDL resetting.
2. Turn on the power once again.
9004 There is an error in the communication (PAI) with an external controller. 1. Turn on the power once main.
2. Check the connection of the open I/F board and the cable.
3. Replace the board for the external controller open I/F.
4. Replace the main board.
9005 There is a fault in the connector of the vide cable to the external controller. 1. Turn on the power once main.
2. Check the connection of the open I/F board and the cable.
3. Replace the board for the external controller open I/F.
4. Replace the main board.
A006 The PDL board does not respond. A subbootable is faulty or absent. 1. Execute PDL resetting.
2. Turn on the power once again.
3. Check the connection of the SURF board.
4. Re-install the firmware.
5. Replace the main board.
A007 There is a mismatch between the control software of the machine and the PDL
control software in regard to version.
1. Execute PDL resetting.
2. Turn on the power once again.
3. Execute system formatting (all), and reinstall the system.
B013 There is corruption in the font data. 1. Turn on the power once again.
2. Re-install the software.
3. Execute system formatting (all), and reinstall the system.
E732 There is an error in the communication with the scanner.
0001 There is a DDI-S communication error. 1. Check the connector used to connect the scanner.
2. Check the power supply of the scanner (to see if initialization takes place at
startup).
3. Replace the reader controller, scanner board, or main board as necessary.
0010 Fault in detection of DDI-S Vsync signal
9999 A scanner is first detected from the printer model. (Not an error code but only
the message 'Turn the main power switch OFF&ON again' is displayed on the
users screen. The error is recorded in service mode > DISPLAY > ERR.
Turn the main power switch off/on
E733 There is an error in the communication with the printer.
0000 At startup, communication with the printer fails. 1. Check the connector used to connect to the printer.
2. Check the power supply of the printer (to see if initialization takes place at
startup).
3. Replace the DC controller or the main board.
0001 There is a DDI-P communication error. 1. Check the connection with the printer.
2. Check the power supply of the printer (to see if initialization takes place at
startup).
3. Replace the DC controller or the main board.
0010 Fault in detection of DDI-P Vsync signal 1. Check the connection with the printer.
2. Check the power supply of the printer (to see if initialization takes place at
startup).
3. Replace the DC controller or the main board.
0020 Error in DDI-P communication 1. Check the connection with the printer.
2. Check the power supply of the printer (to see if initialization takes place at
startup).
3. Replace the DC controller or the main board.
0021 Error in DDI-P communication 1. Check the connection with the printer.
2. Check the power supply of the printer (to see if initialization takes place at
startup).
3. Replace the DC controller or the main board.
E740 There is an error on the Ether board.
0002 The MAC address is illegal. Replace the LAN card.
E743 There is an error in the DDI communication.
0000 An SCI error has occurred. The received data is faulty. A reception timeout
condition has occurred. An SEQ timeout error has occurred.
Disconnect and then connect the flexible cable used to connect the reader unit
and the printer unit. Replace the following as necessary: flexible cable, reader
controller PCB, main controller PCB.
E744 There is an error in the language file/boot ROM.
0001 The version of the language file on the HDD and that of the bootable do not
match.
Download a language file of the correct version.
0002 The size of the language file on the HDD is too large. Download a language file of the correct version.
0003 There is no language file on the HDD indicated by config.txt for a switchover. Download a language file of the correct version.
0004 An attempt to switchover to a language on the HDD fails. Download a language file of the correct version.
1000 The boot ROM that is mounted is of the wrong type. Replace the boot ROM with one of the model in question.
2000 The engine ID indicated by the software ID is illegal. Replace it with a software ID of the correct model.
3xxx Disagreement between the installed memory and the boot ROM Confirm and correct the installed memory and the boot ROM.
E745 There is a fault on the TokenRing board.
0001 An attempt at PCI initialization has failed. 1. Disconnect and then connect the TokenRing board.
2. Replace the TokenRing board.
0002 The MAC address is faulty. 1. Replace the TokenRing board.
0003 There is an error in the acquisition/setting of board information. 1. Replace the TokenRing board.
Code Cause Remedy