Canon iR3245, Service Manual

Page: 472 / 746

Chapter 16
16-4
16.1.4 E400, E413, E490 (ADF)
0019-8896
iR3225 / iR3225N / iR3235 / iR3235N / iR3245 / iR3245N
T-16-4
0530 Device: timeout error
[Location to be detected] image process module (JPEN)
[Detection timing] when there is no interruption 2 min after the
operation has been started.
Turn OFF and then ON the power. Replace the main controller PCB
if this occurs frequently.
0531 Device: abnormal termination error
[Location to be detected] image process module (JPEN)
[Detection timing] when abnormal interruption is detected after the
operation has been started.
Turn OFF and then ON the power. Replace the main controller PCB
if this occurs frequently.
0540 Device: timeout error
[Location to be detected] image process module (JPDE)
[Detection timing] when there is no interruption 2 min after the
operation has been started.
Turn OFF and then ON the power. Replace the main controller PCB
if this occurs frequently.
0541 Device: abnormal termination error
[Location to be detected] image process module (JPDE)
[Detection timing] when abnormal interruption is detected after the
operation has been started.
Turn OFF and then ON the power. Replace the main controller PCB
if this occurs frequently.
0550 Device: timeout error
[Location to be detected] image process module (PRIP)
[Detection timing] when there is no interruption 2 min after the
operation has been started.
Check connection with DDI-P cable(DCON). Replace the main
controller PCB.
0551 Device: abnormal termination error
[Location to be detected] image process module (PRIP)
[Detection timing] when abnormal interruption is detected after the
operation has been started.
Check connection with DDI-P cable(DCON). Replace the main
controller PCB.
0560 Device: timeout error
[Location to be detected] image process module (PRIO)
[Detection timing] when there is no interruption 2 min after the
operation has been started.
Check connection with DDI-P cable(DCON). Replace the main
controller PCB.
0561 Device: abnormal termination error
[Location to be detected] image process module (PRIO)
[Detection timing] when abnormal interruption is detected after the
operation has been started.
Check connection with DDI-P cable(DCON). Replace the main
controller PCB.
Code Cause/Detection Details Measures
E400 A communication error is detected for a certain period of time after communication with the engine started at the time of initialization.
0001 The checksum values of data received from the ADF driver
PCB are inconsistent for a certain period of time.
Check connection of ADF lattice cable (cleaning of connecting point). Replace the
AC driver PCB. Replace the reader controller PCB. Replace the main controller PCB.
0002 The status of data received from the ADF driver PCB is not
normal for a certain period of time.
Check connection of ADF lattice cable (cleaning of connecting point). Replace the
AC driver PCB. Replace the reader controller PCB. Replace the main controller PCB.
0003 A serial communication error interrupt is detected for a certain
period of time.
Check connection of ADF lattice cable (cleaning of connecting point). Replace the
AC driver PCB. Replace the reader controller PCB. Replace the main controller PCB.
E413 Failure in the separation motor (The level of the separation motor HP sensor does not change within a specified period even when the separation
motor is driven.)
0001 The separation roller is in the OPEN status when initializing
the separation motor.
Replace the separation motor HP sensor. Replace the separation motor. Replace the
ADF driver PCB.
0002 The separation roller is in the CLOSE status when initializing
the separation motor.
Replace the separation motor HP sensor. Replace the separation motor. Replace the
ADF driver PCB.
E490 The ADF installed is not supported.
0001 Error with an incorrect ADF model The ADF installed is not supported. Replace the DC controller PCB.
Code Cause Remedy