manualshive.com logo in svg

YASKAWA MOTOMAN DX100, Руководство по обслуживанию, Страница: 718 / 729

Поделиться
Скачать
YASKAWA MOTOMAN DX100 Скачать руководство пользователя страница 718

10

LED Indicator on Circuit Board

DX100

10.3 7 SEG-LED Indicator

10-4

10.3.0.1

7 SEG-LED Indicator Status (1-digit indication) of Each Unit at Error Occurrence

YIF01

All Lit

The power has been turned ON.

0

The booting program has started.

1

The system program has started. (Starts up initializations of various kinds.)

2

Starts verifying the existence of other circuit boards. (Verifies the start-up of the booting program.)

3

Starts the system program transmission.

4

Sends the request of the system program start-up.

5

Starts verifying the existence of other circuit boards. (Verifies the start-up of the system program.)

6

Acquires hardware information, etc. of other circuit boards. (Verifies the IO board status, servo IF, 
and so on.)

7

Starts the CMOS data transmission.

8

Sends the pre-online request.

9

Waits for CERF communication synchronization.

A

B

Sends the start-up request of on-line system.

C

The on-line system has started. (Starts up the initialization task.)

D

Processes the DX100 setup completion.  (Servo ON enabled)

E

Alarm occurs at the DX100 setup.

F

The maintenance system is starting up.

P

Communications interrupted between NCP01 and the programming pendant.

U

Updating system software through network.

EAXA01

All Lit

The power has been turned ON.

0

The booting program has started. (ROM/RAM/FP register check)

1

Starts the booting system. (Completes initializations of various kinds.)

2

Completes the preparation for receiving the system program.  

3

The system program has been received. (Waits for the request of system change.)

4

The system program has started. (Starts up hardware initializations of various kinds.)

5

Starts the system. (Completes initializations of various kinds.)

6

Starts the CMOS data transmission.

7

Receives the CERF mapping. (Waits for pre-online)

8

Starts the servo system. (Starts the process of various initializations.)

9

Waits for RIF communication synchronization. (Completes the process of various initializations.)

A

B

Waits for the start-up of on-line system.

C

D

Completes the DX100 setup process. (Servo ON enabled)

Содержание MOTOMAN DX100


























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов