manualshive.com logo in svg

YASKAWA MOTOMAN DX100, Руководство по обслуживанию, Страница: 46 / 729

Поделиться
Скачать
YASKAWA MOTOMAN DX100 Скачать руководство пользователя страница 46

5

Replacing Parts

DX100

5.1

Replacing DX100 Parts

5-12

5.1.2

Replacing the SERVOPACK

There are two kinds of SERVOPACKs.

Replacement Procedure 

1. Turn OFF the breaker and the primary power supply and wait at least 5 

minutes before replacement Do not touch any terminals during this 
period.

2. Verify that the SERVOPACK charge lamp (red LED) is unlit.

3. Disconnect all the cables connected externally to the SERVOPACK.

(1) Converter control signal connector (CN553)

(2) DC Control power supply connector (CN551)

(3) Control power supply input connector (CN551)

(4) Brake control signal connector (CN513)

(5) Control power supply input connector (CN509)

(6) SHOCK signal input connector (CN512)

(7) Ground terminal connectors (EAXA base)

(8) Control communication connector (CN515)

(9) I/O communication connector (CN517)

(10)  Encoder signal connector (CN508)

4. Put the disconnected cable to the right side of the SERVOPACK

5. Unscrew two EAXA base fixing screws.  (lower side)

6. Unscrew two EAXA base fixing screws.  (upper side)

7. Open the EAXA base.

8. Disconnect all the cables from the amplifier to be replaced.

WARNING

•

After turning OFF the power supply, wait at least 5 minutes 
before replacing a SERVOPACK. Do not touch any terminals 
during this period.

Failure to observe this warning may result in electric shock.

Type

Manipulator

Integrated Type

MH5L, MH6, MA1400, MA1900, 
HP20D, HP20D-6

Separated Type

MH50, MS80, VS50, ES165D, 
ES200DR

Содержание MOTOMAN DX100


























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов