YASKAWA MOTOMAN DX100 Скачать руководство пользователя страница 579

Страница: 579 / 729

DX100

8.3

rm Me

ssa
ge List

8-464

CPU2 detected an error of
contactor 1 enable signal by the
self-diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of
contactor 2 enable signal by the
self-diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of external
overrun 2 signal by the self-
diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of
contactor 3 enable signal by the
self-diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of external
overrun 3 signal by the self-
diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of
contactor 4 enable signal by the
self-diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of external
overrun 4 signal by the self-
diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

CPU2 detected an error of link
signal between YSU unit by the
self-diagnostic check.

YSU unit failure

(1)Reset the alarm.
(2)If the alarm occurs again, replace the YSU unit. Save the CMOS.BIN
before replacing the YSU unit to be safe.

Alarm

Number

Alarm Name

Sub

Code

Meaning

Cause

Remedy

Содержание MOTOMAN DX100


























































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MOTOMAN DX100

Отзывы:

YASKAWA MOTOMAN DX100, Руководство по обслуживанию, Страница: 579 / 729

Результаты поиска

Содержание MOTOMAN DX100

Отзывы: