manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

VDC(diag)-44

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK OUTPUT OF ABS WHEEL SPEED 
SENSOR USING SUBARU SELECT MONI-
TOR.

1) Select {Current Data Display & Save} in 
Subaru Select Monitor.
2) Read the defective ABS wheel speed sen-
sor output.

Does the speed indicated on 
the display change in response 
to the speedometer reading 
during acceleration/decelera-
tion when the steering wheel is 
in the straight-ahead position?

Go to step 

2

.

Go to step 

7

.

2

CHECK POOR CONTACT OF CONNECTOR.

Turn the ignition switch to OFF.

Is there poor contact of connec-
tors between VDCCM&H/U and 
ABS wheel speed sensor?

Repair the connec-
tor.

Go to step 

3

.

3

CHECK CAUSE OF SIGNAL NOISE.

Make sure the radio wave devices and elec-
tronic components are installed correctly.

Are the radio wave devices and 
electronic components 
installed correctly?

Go to step 

4

.

Install the radio 
wave devices and 
electronic compo-
nents properly.

4

CHECK CAUSE OF SIGNAL NOISE.

Check if the noise sources (such as an 
antenna) are installed near the sensor harness.

Are noise sources installed?

Install the noise 
sources apart from 
sensor harness.

Go to step 

5

.

5

CHECK VDCCM&H/U.

1) Connect all connectors.
2) Clear the memory. <Ref. to VDC(diag)-24, 
Clear Memory Mode.>
3) Perform the Inspection Mode. <Ref. to 
VDC(diag)-23, Inspection Mode.>
4) Read the DTC.

Is the same DTC displayed?

Replace the 
VDCCM only. 
<Ref. to VDC-9, 
REPLACEMENT, 
VDC Control Mod-
ule and Hydraulic 
Control Unit 
(VDCCM&H/U).>

Go to step 

6

.

6

CHECK OTHER DTC DETECTION.

Is any other DTC displayed?

Perform the diag-
nosis according to 
DTC. <Ref. to 
VDC(diag)-33, List 
of Diagnostic Trou-
ble Code (DTC).>

It results from a 
temporary noise 
interference.

7

CHECK INSTALLATION OF ABS WHEEL 
SPEED SENSOR.

Is the ABS wheel speed sen-
sor installation bolt tightened 
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)?

Go to step 

8

.

Tighten the ABS 
wheel speed sen-
sor installation 
bolts.

8

CHECK ABS WHEEL SPEED SENSOR SIG-
NAL.

1) Install the ABS wheel speed sensor.
2) Prepare an oscilloscope.
3) Check the ABS wheel speed sensor. <Ref. 
to ABS-14, ABS WHEEL SPEED SENSOR, 
INSPECTION, Front ABS Wheel Speed Sen-
sor.>

Does the oscilloscope indicate 
the waveform pattern like 
shown in the figure when the 
tire is slowly turned? Does the 
oscilloscope indication repeat 
the waveform pattern like 
shown in the figure when the 
tire is slowly turned in equal 
speed for one rotation or more?

Go to step 

10

.

Go to step 

9

.

9

CHECK ABS WHEEL SPEED SENSOR OR 
MAGNETIC ENCODER.

Are there foreign matter, break-
age or damage at the tip of ABS 
wheel speed sensor or mag-
netic encoder?

Remove dirt thor-
oughly. Also 
replace the ABS 
wheel speed sen-
sor or magnetic 
encoder as a unit 
with hub unit bear-
ing if it is broken or 
damaged.

Go to step 

10

.

10

CHECK CAUSE OF SIGNAL NOISE.

Make sure the radio wave devices and elec-
tronic components are installed correctly.

Are the radio wave devices and 
electronic components 
installed correctly?

Go to step 

11

.

Install the radio 
wave devices and 
electronic compo-
nents properly.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Fass Titanium Series Installation Manual preview
Titanium Series
Бренд: Fass Страницы: 13
Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
Kargo Master 4A82T Installation Manual preview
4A82T
Бренд: Kargo Master Страницы: 6
A-Tach 50092 Quick Start Manual preview
50092
Бренд: A-Tach Страницы: 2
VDO RUDDER ANGLE INDICATOR Installation Instructions Manual preview
RUDDER ANGLE INDICATOR
Бренд: VDO Страницы: 8
Chevrolet 1996 Cavalier Owner'S Manual preview
1996 Cavalier
Бренд: Chevrolet Страницы: 372
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Бренд: Axxess Страницы: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Бренд: Dodge Страницы: 276
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Бренд: RAM Страницы: 360
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Бренд: iQOS Страницы: 4
Acura 2003 3.2 TL Owner'S Manual preview
2003 3.2 TL
Бренд: Acura Страницы: 347
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
PERODUA Aruz 2019 Quick User Manual preview
Aruz 2019
Бренд: PERODUA Страницы: 43
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Бренд: Quadratec Страницы: 2
Truma Mover S Installation & Operation Instructions preview
Mover S
Бренд: Truma Страницы: 16
Technaxx FMT1200BT User Manual preview
FMT1200BT
Бренд: Technaxx Страницы: 59

Бренды по названию

Популярные бренды

Загрузить еще бренды