manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-41

Subaru Select Monitor

ENGINE (DIAGNOSTICS)

4. READ FREEZE FRAME DATA FOR ENGINE (OBD MODE)

1) On «Main Menu» display, select {Each System Check}.
2) On «System Selection Menu» display, select {Engine Control System}.
3) Click the [OK] button after the information of engine type has been displayed.
4) On «Engine Diagnosis» display, select {OBD System}.
5) On «OBD Menu» display, select {Freeze Frame Data Display}.
• A list of the support data is shown in the following table.

NOTE:
For detailed operation procedures, refer to “PC application help for Subaru Select Monitor”.

5. V.I.N. REGISTRATION

1) On «Main Menu» display, select {Each System Check}.
2) On «System Selection Menu» display, select {Engine Control System}.
3) Click the [OK] button after the information of engine type has been displayed.
4) On «Engine Diagnosis» display, select {Entry VIN}.
5) Perform the procedures shown on the display screen.

NOTE:
For detailed operation procedures, refer to “PC application help for Subaru Select Monitor”.

Contents

Display

Unit of measure

DTC of freeze frame data

Freeze frame data

DTC

Air fuel ratio control system for bank 1

Fuel system for Bank 1

 — 

Engine load data

Calculated load value

%

Engine coolant temperature signal

Coolant Temp.

°C or °F

Short term fuel trim by front oxygen (A/F) sensor (Bank 1)

Short term fuel trim B1

%

Long term fuel trim by front oxygen (A/F) sensor (Bank 1)

Long term fuel trim B1

%

Intake manifold absolute pressure signal

Mani. Absolute Pressure

mmHg, kPa, inHg or psi

Engine speed signal

Engine Speed

rpm

Vehicle speed signal

Vehicle Speed

km/h or MPH

Ignition timing adv. #1

Ignition timing adv. #1

°

Intake air temperature

Intake Air Temp.

°C

Amount of intake air

Mass Air Flow

g/s

Throttle valve angle

Throttle Opening Angle

%

Secondary air control status

Secondary air system

 — 

Oxygen sensor #12

Oxygen sensor #12

V

A/F correction #12

Short term fuel trim #12

%

OBD system

OBD system

 — 

Oxygen sensor #11

Oxygen sensor #11

Supported

Oxygen sensor #12

Oxygen sensor #12

Supported

Elapsed time after starting engine

Time Since Engine Start

sec

Evaporative purge

Commanded Evap Purge

%

Fuel level

Fuel level

%

Fuel tank pressure

Fuel Tank Pressure

mmHg, kPa, inHg or psig

Atmospheric pressure

Atmosphere Pressure

mmHg, kPa, inHg or psig

ECM power supply voltage

Control module voltage

V

Absolute load

Absolute Load Value

%

A/F target lambda

Target Equivalence Ratio

 — 

Relative throttle opening angle

Relative Throttle Pos.

%

Ambient temperature

Ambient Temperature

°C or °F

Absolute throttle opening angle 2

Absolute Throttle Pos.#2

%

Absolute accelerator opening angle 1

Accelerator Pedal Pos.#1

%

Absolute accelerator opening angle 2

Accelerator Pedal Pos.#2

%

Target throttle opening angle

Target Throt. Act. Cont.

%

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Бренд: Tesla Страницы: 9
EUFAB 12015 Manual preview
12015
Бренд: EUFAB Страницы: 12
Audi A4 2016 Quick Questions And Answers preview
A4 2016
Бренд: Audi Страницы: 9
Belkin WIC004 Setting Up preview
WIC004
Бренд: Belkin Страницы: 4
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
UGREEN Car Cup Holder Phone Mount Manual preview
Car Cup Holder Phone Mount
Бренд: UGREEN Страницы: 9
Audiovox Code Alarm PROFESSIONAL SERIES CA 5550SST Owner'S Manual preview
Code Alarm PROFESSIONAL SERIES CA 5550SST
Бренд: Audiovox Страницы: 14
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Бренд: Hyundai Страницы: 280
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
Belkin F8V9017 User Manual preview
F8V9017
Бренд: Belkin Страницы: 2
Fisher Body FOLDING TOP 1971 Service Manual preview
FOLDING TOP 1971
Бренд: Fisher Body Страницы: 37
Manik 519952T Installation Instructions preview
519952T
Бренд: Manik Страницы: 2
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Бренд: Honda Страницы: 268
GYS 029422 Manual preview
029422
Бренд: GYS Страницы: 32
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды