manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

SE-10

Front Seat

SEATS

2. PASSENGER’S SEAT

CAUTION:
Make sure to adhere to the following rules when
assembling the passenger seat. Improper work
procedures can cause the passenger detection
system to not operate properly.
• If the seat cushion cover is removed or re-
placed, make sure to perform occupant detec-
tion system adjustment after installing the seat.
<Ref. to OD(diag)-15, SYSTEM CALIBRATION
(REZEROING), OPERATION, Subaru Select
Monitor.>
Failure to do so may prevent the passenger’s
airbag from operating properly.
• The passenger detection system (passenger
seat only) control unit, passenger detection
sensor, seat cushion pad and seat cushion
frame are considered as a single seat cushion
pad and frame assembly. Never remove the
passenger detection control unit or the pres-
sure sensor from the seat cushion frame.
• If the seat cushion cover is removed, make
sure to replace the hang wire on the seat cush-
ion side with a new wire.
• Make sure to install the hog rings/clips to the
specified locations. Do not reuse hog rings.

1) Assemble the seat cushion in the reverse order
of disassembly.
2) Assemble the backrest in the reverse order of
disassembly.
3) When installing the backrest assembly to the
seat cushion assembly, fill the gap in the front side
of slide rail LH and in the rear side of slide rail RH
with cloth etc. in order to stabilize the seat cushion
assembly.

4) Temporarily tighten the reclining hinge bolts in
the order of (1) through (4) to an extent that the seat
backrest assembly is not held securely.

5) Use the reclining lever to place the backrest in
the most upright position, and check the first lock
position of recliner.
6) Hold the seat cushion assembly securely, and
tighten the reclining hinge bolts in the order de-
scribed above until they reach the specified torque.

CAUTION:
Do not touch the backrest assembly when tight-
ening the reclining hinge bolts.

7) Assemble each harness, inner belt assembly
and each cover in the reverse order of removal.

Tightening torque:

Refer to “COMPONENT” of “General Descrip-
tion”. <Ref. to SE-2, FRONT SEAT LH, COM-
PONENT, General Description.>

E: INSPECTION

Check that no tear or fray on the backrest cover
and seat cushion cover.

NOTE:
If the door side of the backrest cover is torn or
frayed, the side airbag may not be deployed prop-
erly. In this case, replace the backrest cover.

SE-00537

(A) Vehicle inside

(B) Vehicle outside

(A)

(B)

(2)

(4)

(3)

(1)

SE-00538

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Бренд: Panasonic Страницы: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Бренд: Panasonic Страницы: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Бренд: Panasonic Страницы: 12
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Бренд: B-Speech Страницы: 24
Brodit ProClip 854208 Manual preview
ProClip 854208
Бренд: Brodit Страницы: 2
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Бренд: ULTIMATE SPEED Страницы: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Бренд: Chevrolet Страницы: 441
TrailFX 2123131 Quick User Manual preview
2123131
Бренд: TrailFX Страницы: 2
Cadillac 2001 Eldorado Owner'S Manual preview
2001 Eldorado
Бренд: Cadillac Страницы: 335
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
Mitsubishi Montero 1988 Manual preview
Montero 1988
Бренд: Mitsubishi Страницы: 367
Arrista SG8-19 Installation Manual preview
SG8-19
Бренд: Arrista Страницы: 2
Dodge Charger SRT 392 2017 Operating Information Manual preview
Charger SRT 392 2017
Бренд: Dodge Страницы: 576
Lexus LS 500h 2022 Owner'S Manual, Quick Manual preview
LS 500h 2022
Бренд: Lexus Страницы: 108
Westin 28-21030 Instructions preview
28-21030
Бренд: Westin Страницы: 3
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Бренд: BMW Страницы: 64
Harbor Freight Tools 95058 Installation And Operation Instructions Manual preview
95058
Бренд: Harbor Freight Tools Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды