manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

AC-14

General Description

HVAC SYSTEM (HEATER, VENTILATOR AND A/C)

C: CAUTION

1. HFC-134A A/C SYSTEM

• The cooling system components for the HFC-
134a system such as the refrigerant and compres-
sor oil are different from the conventional CFC-12
system components and they are incompatible with
each other.
• Vehicles with the HFC-134a system can be iden-
tified by the label (A) attached to the vehicle.
Before maintenance, check which A/C system is in-
stalled to the vehicle.

2. COMPRESSOR OIL

• HFC-134a compressor oil has no compatibility
with that of CFC-12 system.
• Use only the manufacturer-authorized compres-
sor oil for the HFC-134a system; only use DH-PR
(ZXL200PG).
• Do not mix multiple compressor oils.
If CFC-12 compressor oil is used in the HFC-134a
A/C system, the compressor may become stuck
due to poor lubrication, or the refrigerant may leak
due to swelling of rubber parts.
On the other hand, if HFC-134a compressor oil is
used in a CFC-12 A/C system, the durability of the
A/C system will be lowered.
• HFC-134a compressor oil is very hygroscopic.
When replacing or installing/removing A/C parts,
immediately isolate the oil from atmosphere using a
plug or tape. In order to avoid moisture, store the oil
in a container with its cap tightly closed.

3. REFRIGERANT

• CFC-12 refrigerant cannot be used in a HFC-
134a A/C system. HFC-134a refrigerant, also can-
not be used in a CFC-12 A/C system.
• If an incorrect or no refrigerant is used, it will re-
sult in poor lubrication and the compressor itself
may be damaged.

4. HANDLING OF REFRIGERANT

• The refrigerant boils at approx. –30°C (–22°F).
When handling it, be sure to wear protective gog-
gles and protective gloves. Direct contact of the re-
frigerant with skin may cause frostbite.
If the refrigerant gets into your eye, avoid rubbing
your eyes with your hands. Wash your eye with
plenty of water, and receive medical treatment from
an eye doctor.
• Do not heat a service can. If a service can is di-
rectly heated, or put into boiling water, the inside
pressure will become extremely high. This may
cause the can to explode. If a service can must be
warmed up, use warm water of 40°C (104°F) or
less.
• Do not drop or impact a service can. (Observe
the precautions and operation procedure described
on the refrigerant can.)
• When the engine is running, do not open the
high-pressure valve of manifold gauge. The high-
pressure gas will back-flow resulting in an explo-
sion of the can.
• Provide good ventilation and do not work in a
closed area.

(A)

AC-01771

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
RBP STEALTH POWER RBP-216-SP Installation Manual preview
STEALTH POWER RBP-216-SP
Бренд: RBP Страницы: 16
HURST STREET SUPER SHIFTER Installation Instructions preview
STREET SUPER SHIFTER
Бренд: HURST Страницы: 2
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
Yutrax TX107 Operator'S Manual preview
TX107
Бренд: Yutrax Страницы: 8
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Бренд: Safe Fleet Страницы: 24
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Бренд: Black Horse Off Road Страницы: 7
Air Lift 88365 Installation Manual preview
88365
Бренд: Air Lift Страницы: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Бренд: Dolphin Страницы: 16
Quadratec 12057.0102 Installation Manual preview
12057.0102
Бренд: Quadratec Страницы: 8
Toyota Camry Hybrid 2012 Warranty & Maintenance Manual preview
Camry Hybrid 2012
Бренд: Toyota Страницы: 62
Honda Civic Coupe 2009 Owner'S Manual preview
Civic Coupe 2009
Бренд: Honda Страницы: 414
Honda 2008 S2000 Manual preview
2008 S2000
Бренд: Honda Страницы: 280

Бренды по названию

Популярные бренды

Загрузить еще бренды