manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-228

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK CURRENT DATA.

1) Turn the ignition switch to ON.
2) Read the data of fuel tank pressure sensor 
signal using the Subaru Select Monitor or gen-
eral scan tool.
NOTE:
• Subaru Select Monitor
For detailed operation procedures, refer to
“READ CURRENT DATA FOR ENGINE”. <Ref.
to EN(H4DOTC)(diag)-34, Subaru Select Moni-
tor.>
• General scan tool
For detailed operation procedures, refer to the
general scan tool operation manual.

Is the measured value less than 
–7.45 kPa (–55.89 mmHg, 
–2.2003 inHg) ?

Go to step 

2

.

Even if DTC is 
detected, the cir-
cuit has returned to 
a normal condition 
at this time. Repro-
duce the failure, 
and then perform 
the diagnosis 
again.
NOTE:
In this case, tem-
porary poor con-
tact of connector
may be the cause.

2

CHECK FUEL TANK PRESSURE SENSOR 
POWER SUPPLY.

1) Turn the ignition switch to OFF.
2) Disconnect the connector from the fuel tank 
pressure sensor.
3) Turn the ignition switch to ON.
4) Measure the voltage between the fuel tank 
pressure sensor connector and chassis ground.

Connector & terminal

(R47) No. 3 (+) — Chassis ground (–):

Is the voltage 4.5 V or more?

Go to step 

3

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM and fuel tank
pressure sensor
connector
• Poor contact of
ECM connector
• Poor contact of
coupling connector

3

CHECK HARNESS BETWEEN ECM AND 
FUEL TANK PRESSURE SENSOR CONNEC-
TOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM.
3) Measure the resistance of harness between 
the ECM and fuel tank pressure sensor connec-
tor.

Connector & terminal

(B135) No. 32 — (R47) No. 1:

Is the resistance less than 1 

:

? Go to step 

4

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM and fuel tank
pressure sensor
connector
• Poor contact of
coupling connector

4

CHECK HARNESS BETWEEN ECM AND 
FUEL TANK PRESSURE SENSOR CONNEC-
TOR.

Measure the resistance between ECM and 
chassis ground.

Connector & terminal

(B135) No. 32 — Chassis ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

5

.

Repair the ground 
short circuit of har-
ness between 
ECM and fuel tank 
pressure sensor 
connector.

5

CHECK POOR CONTACT.

Check for poor contact between the ECM and 
fuel tank pressure sensor connector.

Is there poor contact of the 
ECM or fuel tank pressure sen-
sor connector?

Repair the poor 
contact of the ECM 
or fuel tank pres-
sure sensor con-
nector.

Replace the fuel 
tank pressure sen-
sor. <Ref. to 
EC(H4DOTC)-18, 
Fuel Tank Pres-
sure Sensor.>

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Бренд: Mazda Страницы: 4
Jeep Compass Overview Manual preview
Compass
Бренд: Jeep Страницы: 25
Falcon 1990 Installation Instructions And Specifications preview
1990
Бренд: Falcon Страницы: 8
Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Honda HRM3000 User Manual preview
HRM3000
Бренд: Honda Страницы: 73
Tessera4x4 SOT-1311 ROLL Installation Manual preview
SOT-1311 ROLL
Бренд: Tessera4x4 Страницы: 20
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Бренд: Hyundai Страницы: 280
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Бренд: MULTILIFT Страницы: 62
Kia Picanto Manual preview
Picanto
Бренд: Kia Страницы: 680
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Бренд: Ford Страницы: 52
Cadillac XLR-V Specifications preview
XLR-V
Бренд: Cadillac Страницы: 2
Buick Cascada 2016 Getting To Know Manual preview
Cascada 2016
Бренд: Buick Страницы: 20
K40 ELECTRONICS K40 Platinum360 Owner'S Manual preview
K40 Platinum360
Бренд: K40 ELECTRONICS Страницы: 11
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Бренд: Honda Страницы: 687
PEUGEOT 5008 2017 Handbook preview
5008 2017
Бренд: PEUGEOT Страницы: 404

Бренды по названию

Популярные бренды

Загрузить еще бренды