manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

PM-30

Front & Rear Differential Gear Oil

PERIODIC MAINTENANCE SERVICES

16.Front & Rear Differential Gear 

Oil

A: INSPECTION

1. FRONT DIFFERENTIAL (AT MODEL)

1) Park the vehicle on a level surface.
2) Remove the differential oil level gauge and wipe
it clean.
3) Reinsert the level gauge all the way. Make sure
the level gauge is inserted correctly and in the
proper orientation.
4) Remove the oil level gauge again, and check the
level of differential gear oil. If the differential gear oil
level is below “L” line, add oil to bring the level up to
“F” line.

NOTE:
To prevent overfilling the differential gear oil, do not
fill oil above the “F” line.

2. REAR DIFFERENTIAL

1) Remove the filler plug, and then check the gear
oil. Replace the gear oil if it is contaminated or de-
teriorated.
2) Check that the gear oil level is up to the bottom
of the filler plug hole. If the level is low, refill up to
the bottom of filler plug.

B: REPLACEMENT

1. FRONT DIFFERENTIAL (MT MODEL)

For MT model, differential oil is used as manual
transmission oil for lubricating the differential. Refer
to “Transmission Oil”. <Ref. to PM-27, Transmis-
sion Gear Oil.>

2. FRONT DIFFERENTIAL (AT MODEL)

1) Lift up the vehicle.
2) Drain the differential gear oil by removing drain
plug using TORX

®

 bit T70.

CAUTION:
If the differential gear oil is spilt over exhaust
pipe, wipe it off with cloth to avoid emitting
smoke or causing a fire.

NOTE:
Before starting work, cool off the differential gear oil
well.

3) Replace the gasket with a new part and tighten
the differential oil drain plug to the specified torque
using the TORX

®

 bit T70.

Tightening torque:

44 N·m (4.5 kgf-m, 32.5 ft-lb) 
(Aluminum gasket silver)
70 N·m (7.1 kgf-m, 51.6 ft-lb) 
(Copper gasket brown)
70 N·m (7.1 kgf-m, 51.6 ft-lb) 
(Metal gasket black)

4) Lower the vehicle.

(A) Oil level gauge

(B) Upper level

(C) Lower level

(A) Filler plug

(B) Drain plug

AT-04840

(B)

(C)

(A)

(A)

DI-00521

(A)

(B)

PM-00384

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Metra Electronics 99-3030B Installation Instructions Manual preview
99-3030B
Бренд: Metra Electronics Страницы: 12
Halfords Exodus 360 Fitting Instructions preview
Exodus 360
Бренд: Halfords Страницы: 4
BMW 3-series convertible Complete Vehicle Workbook preview
3-series convertible
Бренд: BMW Страницы: 98
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Yakima K831 Manual preview
K831
Бренд: Yakima Страницы: 8
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Бренд: Dometic Страницы: 196
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Бренд: Honda Страницы: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Бренд: Pro-gard Страницы: 4
Subaru 360 Sedan Service Manual preview
360 Sedan
Бренд: Subaru Страницы: 16
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Бренд: iOttie Страницы: 58
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Бренд: FVC Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды