manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-327

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

DR:DTC P2109 THROTTLE/PEDAL POSITION SENSOR “A” MINIMUM STOP 

PERFORMANCE

NOTE:
For the diagnostic procedure, refer to DTC P2101. <Ref. to EN(H4DOTC)(diag)-319, DTC P2101 THROT-
TLE ACTUATOR CONTROL MOTOR CIRCUIT RANGE/PERFORMANCE, Diagnostic Procedure with Di-
agnostic Trouble Code (DTC).>

Step

Check

Yes

No

1

CHECK ELECTRONIC THROTTLE CON-
TROL RELAY.

1) Turn the ignition switch to OFF.
2) Remove the electronic throttle control relay.
3) Measure the resistance between electronic 
throttle control relay terminals.

Terminals

No. 29 — No. 30:

Is the resistance 1 M

:

 or 

more?

Go to step 

2

.

Replace the elec-
tronic throttle con-
trol relay. <Ref. to 
FU(H4DOTC)-57, 
Electronic Throttle 
Control Relay.>

2

CHECK SHORT CIRCUIT OF ELECTRONIC 
THROTTLE CONTROL RELAY POWER SUP-
PLY.

1) Turn the ignition switch to ON.
2) Measure the voltage between electronic 
throttle control relay connector and chassis 
ground.

Connector & terminal

(B220) No. 30 (+) — Chassis ground (–):

Is the voltage 10 V or more?

Repair the short 
circuit to power in 
the harness 
between ECM and 
electronic throttle 
control relay con-
nector.

Go to step 

3

.

3

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL RE-
LAY CONNECTOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM.
3) Measure the resistance between ECM and 
chassis ground.

Connector & terminal

(B136) No. 21 — Chassis ground:

Is the resistance 1 M

:

 or 

more?

Repair the poor 
contact of ECM 
connector.

Repair the short 
circuit in harness 
to ground between 
ECM and elec-
tronic throttle con-
trol relay 
connector.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
Webasto Transit Vancouver Wagon Manual preview
Transit Vancouver Wagon
Бренд: Webasto Страницы: 44
Whispbar K728W Fitting Instructions Manual preview
K728W
Бренд: Whispbar Страницы: 85
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
JKS OGS125 Installation Instructions preview
OGS125
Бренд: JKS Страницы: 3
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
Pacbrake HP10098 Installation Manual preview
HP10098
Бренд: Pacbrake Страницы: 6
Flash Cover MN019 Instructions preview
MN019
Бренд: Flash Cover Страницы: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Бренд: Porsche Страницы: 98
Sanitas SMG 245 Instructions For Use Manual preview
SMG 245
Бренд: Sanitas Страницы: 36
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Paccar PACCHARGE AC20 Installation Manual preview
PACCHARGE AC20
Бренд: Paccar Страницы: 63
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Бренд: ECS Страницы: 4
Whispbar WB751 Manual preview
WB751
Бренд: Whispbar Страницы: 15
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
Navman T1 F20 User Manual preview
T1 F20
Бренд: Navman Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды