manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4SO)(diag)-205

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK FUEL FILLER CAP.

1) Turn the ignition switch to OFF.
2) Check the fuel filler cap.
NOTE:
The DTC is stored in memory if fuel filler cap is
or was loose or if the cap chain has caught while
tightening.

Is the fuel filler cap tightened 
securely?

Go to step 

2

.

Tighten fuel filler 
cap securely.

2

CHECK FUEL FILLER CAP.

Is the fuel filler cap genuine?

Go to step 

3

.

Replace with a 
genuine fuel filler 
cap.

3

CHECK FUEL FILLER PIPE GASKET.

Is there any damage to the seal 
between fuel filler cap and fuel 
filler pipe?

Repair or replace 
the fuel filler cap 
and fuel filler pipe. 
<Ref. to 
FU(H4SO)-61, 
Fuel Filler Pipe.>

Go to step 

4

.

4

CHECK DRAIN VALVE.

1) Connect the delivery (test) mode connector.
2) Turn the ignition switch to ON.
3) Operate the drain valve using the Subaru 
Select Monitor.
NOTE:
The drain valve can be operated using Subaru
Select Monitor. For the procedures, refer to
“Compulsory Valve Operation Check Mode”.
<Ref. to EN(H4SO)(diag)-56, Compulsory
Valve Operation Check Mode.>

Does the drain valve operate?

Go to step 

5

.

Replace the drain 
valve. <Ref. to 
EC(H4SO)-19,
Drain Valve.>

5

CHECK PURGE CONTROL SOLENOID 
VALVE.

Operate the purge control solenoid valve using 
the Subaru Select Monitor.
NOTE:
Purge control solenoid valve operation can be
executed using Subaru Select Monitor. For the
procedures, refer to “Compulsory Valve Opera-
tion Check Mode”. <Ref. to EN(H4SO)(diag)-
56, Compulsory Valve Operation Check
Mode.>

Does the purge control sole-
noid valve operate?

Go to step 

6

.

Replace the purge 
control solenoid 
valve. <Ref. to 
EC(H4SO)-9,
Purge Control 
Solenoid Valve.>

6

CHECK PRESSURE CONTROL SOLENOID 
VALVE.

Operate the pressure control solenoid valve 
using the Subaru Select Monitor.
NOTE:
The pressure control solenoid valve operation
can be executed using the Subaru Select Mon-
itor. For the procedures, refer to “Compulsory
Valve Operation Check Mode”. <Ref. to
EN(H4SO)(diag)-56, Compulsory Valve Opera-
tion Check Mode.>

Does the pressure control sole-
noid valve operate?

Go to step 

7

.

Replace the pres-
sure control sole-
noid valve. <Ref. to 
EC(H4SO)-16,
Pressure Control 
Solenoid Valve.>

7

CHECK EVAPORATIVE EMISSION CON-
TROL SYSTEM LINE.

1) Turn the ignition switch to OFF.
2) Disconnect the delivery (test) mode connec-
tor.

Is there any hole of more than 
1.0 mm (0.04 in) dia. on evapo-
ration line?

Repair or replace 
the evaporation 
line. <Ref. to 
FU(H4SO)-76, 
Fuel Delivery and 
Evaporation 
Lines.>

Go to step 

8

.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

EAL Formula 523585 Assembly Instructions preview
Formula 523585
Бренд: EAL Страницы: 4
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
TBC DPI1K User Manual preview
DPI1K
Бренд: TBC Страницы: 12
Condor T-RAMP Quick Start Manual preview
T-RAMP
Бренд: Condor Страницы: 2
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Бренд: Jeep Страницы: 380
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Бренд: Saab Страницы: 15
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Бренд: Oldsmobile Страницы: 380
Brink 4698 Fitting Instructions Manual preview
4698
Бренд: Brink Страницы: 26
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
Rigid Hitch BULL BAR Installation Instructions preview
BULL BAR
Бренд: Rigid Hitch Страницы: 2
Cadillac 2005 XLR Owner'S Manual preview
2005 XLR
Бренд: Cadillac Страницы: 438
Oldsmobile ALERO 2001 Owner'S Manual preview
ALERO 2001
Бренд: Oldsmobile Страницы: 340
Datsun Saloon I300 Workshop Manual preview
Saloon I300
Бренд: Datsun Страницы: 104
Sanixair 8059606830094 Use And Maintenance preview
8059606830094
Бренд: Sanixair Страницы: 20
OMNISTOR OMNI-BIKE plus Caravan Special Manual preview
OMNI-BIKE plus Caravan Special
Бренд: OMNISTOR Страницы: 4
VDO FUEL TANK GAUGE Installation Instructions Manual preview
FUEL TANK GAUGE
Бренд: VDO Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды