manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

ME(H4DOTC)-96

Cylinder Block

MECHANICAL

8) The replacement procedure for the connecting
rod small end bushing is as follows.

(1) Remove the bushing from connecting rod
with ST and press.
(2) Press the bushing with the ST after applying
oil on the periphery of new bushing.

ST

499037100

CONNECTING ROD 
BUSHING REMOVER AND 
INSTALLER

(3) Make two 3 mm (0.12 in) holes in the
pressed bushing to match the pre-manufac-
tured holes on the connecting rod, then ream
the inside of the bushing.
(4) After completion of reaming, clean the bush-
ing to remove chips.

6. CRANKSHAFT AND CRANKSHAFT 
BEARING

1) Clean the crankshaft completely, and check it for
cracks using liquid penetrant tester. If defective, re-
place the crankshaft.
2) Measure warping of the crankshaft. If it exceeds
the limit, correct or replace it.

NOTE:
If a suitable V-block is not available, using just the
#1 and #5 crankshaft bearings on cylinder block,
position the crankshaft on cylinder block. Then,
measure the crankshaft bend using a dial gauge.

Crankshaft bend limit:

0.035 mm (0.0014 in)

3) Inspect the crank journal and crank pin for wear.
If they are not within the standard, replace the bear-
ing with a suitable (undersize) one, and replace or
grind to correct the crankshaft as necessary. When
grinding the crank journal or crank pin, finish them
to the specified dimensions according to the under-
size bearing to be used.

Crank pin:

Out-of-roundness

0.003 mm (0.0001 in)

Cylindricality

0.004 mm (0.0002 in)

Grinding limit (dia.)

To 51.750 mm (2.0374 in)

Crank journal:

Out-of-roundness

0.005 mm (0.0002 in)

Cylindricality

0.006 mm (0.0002 in)

Grinding limit (dia.)

To 59.758 mm (2.3527 in)

ME-00182

ST

ME-00183

ME-00184

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Бренд: Jeep Страницы: 608
RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Бренд: RACLET Страницы: 48
RACLET Allegra Manual preview
Allegra
Бренд: RACLET Страницы: 31
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Бренд: SuperATV Страницы: 3
iArmor EDGE IA-N098 Quick Start Manual preview
EDGE IA-N098
Бренд: iArmor Страницы: 4
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Webasto Telestart T91 Installation Instructions Manual preview
Telestart T91
Бренд: Webasto Страницы: 18
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
cam 40103 AL Mounting Instructions preview
40103 AL
Бренд: cam Страницы: 6
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Бренд: Mercedes-Benz Страницы: 91
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Бренд: TEINHOF Страницы: 2
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Бренд: Bulldog Security Страницы: 7
Honda 2000 RL Owner'S Manual preview
2000 RL
Бренд: Honda Страницы: 330
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Бренд: Mercedes-Benz Страницы: 66

Бренды по названию

Популярные бренды

Загрузить еще бренды