manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

BR-37

Air Bleeding

BRAKE

14.Air Bleeding

A: PROCEDURE

CAUTION:
• Do not let brake fluid come into contact with
the painted surface of the vehicle body. Wash
away with water immediately and wipe off if it is
spilled by accident.
• Avoid mixing brake fluid of different brands
to prevent fluid performance from degrading.
• Be careful not to allow dirt or dust to enter the
reservoir tank.

1. MASTER CYLINDER

NOTE:
• When the master cylinder is disassembled or the
reservoir tank is empty, bleed the master cylinder.
• If bleeding of the master cylinder is not neces-
sary, omit the following procedures, and perform
bleeding of the brake line. <Ref. to BR-37, BRAKE
LINE, PROCEDURE, Air Bleeding.>
1) Fill the reservoir tank of the master cylinder with
brake fluid.

NOTE:
While bleeding air, keep the reservoir tank filled
with brake fluid to prevent entry of air.
2) Disconnect the brake line at primary and sec-
ondary sides.
3) Wrap the master cylinder with a plastic bag.
4) Depress the brake pedal slowly and hold it.

NOTE:
On the model with brake assist mechanism, the fol-
lowing phenomena occur when the brake pedal is
depressed. However, those are not malfunction but
the phenomena that occur when the brake assist
mechanism functions properly.
• Brake feel is soft when brake pedal is depressed
hard or quicker than usual.
• A light crack is heard when brake pedal is de-
pressed hard or quicker than usual.

5) Plug the outlet plug with your finger, and then re-
lease the brake pedal.

6) Repeat the step 4) and 5) several times.
7) Remove the plastic bag.
8) Install the brake pipe to the master cylinder.

Tightening torque:

Model with ABS

15 N·m (1.5 kgf-m, 11.1 ft-lb)

Model with VDC

19 N·m (1.9 kgf-m, 14 ft-lb)

9) Bleed air from the brake line. <Ref. to BR-37,
BRAKE LINE, PROCEDURE, Air Bleeding.>

2. BRAKE LINE

1) When the master cylinder is disassembled or the
reservoir tank is empty, bleed the master cylinder
before bleeding the brake line. <Ref. to BR-37,
MASTER CYLINDER, PROCEDURE, Air Bleed-
ing.>
2) Fill the reservoir tank of the master cylinder with
brake fluid.

NOTE:
While bleeding air, keep the reservoir tank filled
with brake fluid to prevent entry of air.
3) Attach one end of the vinyl tube to the air bleeder
and the other end to the brake fluid container.

4) Depress the brake pedal several times, and hold
it.
5) Loosen the air bleeder screw to drain brake fluid.
Tighten the air bleeder quickly, and release the
brake pedal.
6) Repeat the steps 4) to 5) until there are no more
air bubbles in the vinyl tube.

BR-00090

BR-00091

BR-00087

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Бренд: Panasonic Страницы: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Бренд: Panasonic Страницы: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Бренд: Panasonic Страницы: 12
AA Products X31 Instruction Manual preview
X31
Бренд: AA Products Страницы: 6
Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Бренд: Audiovox Страницы: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Бренд: Volvo Страницы: 138
AMP Research 75135-01A Installation Manual preview
75135-01A
Бренд: AMP Research Страницы: 12
Havis-Shields Half Size Trunk Box Organizer C-TBO-CV Installation Instructions preview
Half Size Trunk Box Organizer C-TBO-CV
Бренд: Havis-Shields Страницы: 1
Volvo S60 2012 Quick Manual preview
S60 2012
Бренд: Volvo Страницы: 8
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
Saab 9000 1985 Service Manual preview
9000 1985
Бренд: Saab Страницы: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Бренд: A-rival Страницы: 23
Faria Fuel Manager Owner'S Manual preview
Fuel Manager
Бренд: Faria Страницы: 12
Honeywell Thor VM1A Quick Start Manual preview
Thor VM1A
Бренд: Honeywell Страницы: 16
Honeywell Thor VM2C02 User Manual preview
Thor VM2C02
Бренд: Honeywell Страницы: 70
Honeywell Thor VM2C User Manual preview
Thor VM2C
Бренд: Honeywell Страницы: 70
Honeywell Thor VM2 User Manual preview
Thor VM2
Бренд: Honeywell Страницы: 398

Бренды по названию

Популярные бренды

Загрузить еще бренды