manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

AB(diag)-90

Diagnostic Chart with Trouble Code

AIRBAG SYSTEM (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK POOR CONTACT OF CONNEC-
TORS.

Check for poor contact of the connectors 
between the airbag control module and the pas-
senger’s airbag module.

Is there poor contact?

Replace the airbag 
main harness 
along with body 
harness.

Go to step 

2

.

2

CHECK PASSENGER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect 
the ground cable from battery, and wait for 20 
seconds or more.
2) Remove the console front panel and discon-
nect the connectors (AB10) from (AB9).
3) Connect the connector (1P) in the test har-
ness P to connector (AB9).
4) Connect the airbag resistor to the connec-
tors (2P) and (3P) of test harness P.
5) Connect the battery ground terminal and 
turn the ignition switch to ON.

Does the airbag warning light 
illuminate for 6 seconds and go 
off?

Replace the pas-
senger’s airbag 
module. <Ref. to 
AB-16, Passen-
ger’s Airbag Mod-
ule.>

Go to step 

3

.

3

CHECK AIRBAG MAIN HARNESS (PASSEN-
GER’S AIRBAG HARNESS).

1) Turn the ignition switch to OFF, disconnect 
the ground cable from battery, and wait for 20 
seconds or more.
2) Disconnect the airbag resistor from the con-
nectors (2P) and (3P) of test harness P.
3) Remove the instrument panel lower cover 
and disconnect the connector (AB7) from 
(AB2).
4) Disconnect the connectors (AB6, AB17, 
AB18) from the airbag control module, and con-
nect the test harness AG connector (1AG).
5) Measure the voltage between connector 
(3AG) in the test harness AG and chassis 
ground.

Connector & terminal

(3AG) No. 8 (+) — Chassis ground (–):
(3AG) No. 6 (+) — Chassis ground (–):

Is the voltage less than 1 V?

Go to step 

4

.

Replace the airbag 
main harness 
along with body 
harness.

4

CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.
2) Clear the memory.
3) Perform the Inspection Mode.
4) Read the DTC.

Is the same DTC displayed?

Replace the airbag 
control module. 
<Ref. to AB-21, 
Airbag Control 
Module.>

Go to step 

5

.

5

CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using 
“List of Diagnostic 
Trouble Code 
(DTC)”. <Ref. to 
AB(diag)-38, List 
of Diagnostic Trou-
ble Code (DTC).>

Finish the diagno-
sis.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
Parrot CK3300 Setup Information Manual preview
CK3300
Бренд: Parrot Страницы: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Бренд: Parrot Страницы: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Бренд: Parrot Страницы: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Бренд: Parrot Страницы: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Бренд: Parrot Страницы: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Бренд: Parrot Страницы: 106
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
Alpine KCE-G7QI Installation preview
KCE-G7QI
Бренд: Alpine Страницы: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Бренд: Whispbar Страницы: 15
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
Maserati Gransport Owner'S Manual preview
Gransport
Бренд: Maserati Страницы: 210
OnStar liveon Owner'S Manual preview
liveon
Бренд: OnStar Страницы: 22
Caltrend BM110 Installation Instructions preview
BM110
Бренд: Caltrend Страницы: 2
Advanced ICE 1296-1 Manual preview
1296-1
Бренд: Advanced ICE Страницы: 4
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Бренд: Voxoa Страницы: 48
E&G Classics 1398-0502-09 Instruction Manual preview
1398-0502-09
Бренд: E&G Classics Страницы: 2
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды