manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

ABS(diag)-2

Basic Diagnostic Procedure

ABS (DIAGNOSTICS)

1. Basic Diagnostic Procedure

A: PROCEDURE

CAUTION:
Remove foreign matter (dust, water, oil etc.) from the ABSCM&H/U connector during removal and in-
stallation.

NOTE:
• To check harness for open or short circuits, shake the suspected trouble spot or connector.
• Refer to “Check List for Interview”. <Ref. to ABS(diag)-3, Check List for Interview.>

Step

Check

Yes

No

1

CHECK PRE-INSPECTION.

1) Ask the customer when and how the trouble 
occurred using the interview check list. <Ref. to 
ABS(diag)-3, Check List for Interview.>
2) Before performing diagnostics, check the 
components which might affect ABS problems. 
<Ref. to ABS(diag)-7, INSPECTION, General 
Description.>

Are components which might 
affect the ABS problem operat-
ing correctly?

Go to step 

2

.

Repair or replace 
each component.

2

CHECK DTC.

1) Turn the ignition switch to OFF.
2) Connect the Subaru Select Monitor to data 
link connector.
3) Turn the ignition switch to ON and run the 
Subaru Select Monitor.

NOTE:
If the communication function of the Subaru Se-
lect Monitor cannot be executed properly,
check the communication circuit. <Ref. to
ABS(diag)-16, COMMUNICATION FOR INI-
TIALIZING IMPOSSIBLE, INSPECTION, Sub-
aru Select Monitor.>
4) Read the DTC using Subaru Select Monitor. 
<Ref. to ABS(diag)-19, OPERATION, Read 
Diagnostic Trouble Code (DTC).>

Is DTC displayed on the Subaru 
Select Monitor?

Record the DTCs 
and Information in 
Trouble State. Go 
to step 

4

.

Go to step 

3

.

3

PERFORM GENERAL DIAGNOSTICS.

1) Perform the inspection by referring to “Gen-
eral Diagnostic Table”. <Ref. to ABS(diag)-60, 
General Diagnostic Table.>
2) Perform the Clear Memory Mode. <Ref. to 
ABS(diag)-21, Clear Memory Mode.>
3) Perform the Inspection Mode. <Ref. to 
ABS(diag)-20, Inspection Mode.>
4) Read the DTC. <Ref. to ABS(diag)-13, 
HOW TO USE SUBARU SELECT MONITOR, 
OPERATION, Subaru Select Monitor.>
Check the DTC is not displayed.

Does the ABS warning light go 
off after turning the ignition 
switch to ON?

Finish the diagno-
sis.

Check the combi-
nation meter cir-
cuit. <Ref. to 
ABS(diag)-23,
ABS WARNING 
LIGHT DOES NOT 
GO OFF, ABS 
Warning Light / 
Brake Warning 
Light Illumination 
Pattern.>

4

PERFORM DIAGNOSIS.

1) Refer to “List of Diagnostic Trouble Code 
(DTC)”. <Ref. to ABS(diag)-26, LIST, List of 
Diagnostic Trouble Code (DTC).>
2) Correct the cause of trouble.
3) Perform the Clear Memory Mode. <Ref. to 
ABS(diag)-21, Clear Memory Mode.>
4) Perform the Inspection Mode. <Ref. to 
ABS(diag)-20, Inspection Mode.>
5) Read the DTC. <Ref. to ABS(diag)-13, 
HOW TO USE SUBARU SELECT MONITOR, 
OPERATION, Subaru Select Monitor.>

Is DTC displayed?

Repeat step 1 to 4 
until DTC does not 
appear.

Finish the diagno-
sis.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Hama Pico Operating Instructions preview
Pico
Бренд: Hama Страницы: 2
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Cequent 10417 Instruction Sheets preview
10417
Бренд: Cequent Страницы: 9
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Бренд: Mercedes-Benz Страницы: 388
Standby L54 Manual preview
L54
Бренд: Standby Страницы: 10
Phonocar VM338 Mounting Instructions preview
VM338
Бренд: Phonocar Страницы: 6
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
Ecco EC4210B-K Installation And Operation Instructions Manual preview
EC4210B-K
Бренд: Ecco Страницы: 9
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Бренд: Mercedes-Benz Страницы: 39
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Great day UVFR751 Instructions For Installation And Use preview
UVFR751
Бренд: Great day Страницы: 5
Webasto HOLLANDIA 700 - 20 Series Service Manual preview
HOLLANDIA 700 - 20 Series
Бренд: Webasto Страницы: 30
Speedtech 64-67 Instructional Manual preview
64-67
Бренд: Speedtech Страницы: 12
Nos 05183NOS Owner'S Manual preview
05183NOS
Бренд: Nos Страницы: 22
Pyle PLPSC8 User Manual preview
PLPSC8
Бренд: Pyle Страницы: 14
Chevrolet Chevelle 1965 Owner'S Manual preview
Chevelle 1965
Бренд: Chevrolet Страницы: 55
Kuda 050130 Installation Instruction preview
050130
Бренд: Kuda Страницы: 4
X-Armour XR-9500 Installation And Owner'S Manual preview
XR-9500
Бренд: X-Armour Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды