manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

PS-47

Oil Pump

POWER ASSISTED SYSTEM (POWER STEERING)

3. HYDRAULIC PRESSURE

NOTE:
• To measure hydraulic pressure correctly, be
sure to complete all the items in “INSPECTION”,
prior to performing the measurement. <Ref. to PS-
51, INSPECTION, General Diagnostic Table.>
• Do not leave the valve of pressure gauge closed
or hold the steering wheel at lock for 5 seconds or
more in any case, this can damage the oil pump.
• Before attaching a pressure gauge, place cloth
at locations where fluid is expected to spill. Wipe off
any spilt fluid completely after the measurement.
1) Regular pressure measurement

(1) Connect the ST1, ST2 and ST3.

ST1

925711000

PRESSURE GAUGE

ST2

34099AC020

ADAPTER HOSE B

ST3

34099AC010

ADAPTER HOSE A

(2) Remove the air intake duct.
(3) Disconnect the pipe C from pump.
(4) Using the gasket (Part No. 34621AC021)
and bolt (Part No. 34620AC010), install the ST2
to pump instead of pressure hose.
• Non-turbo model

• Turbo model

(5) Attach the ST3 to the end of pressure hose
which is removed from pump.

(6) Replenish power steering fluid up to the
specified level.
(7) Open the valve, and start the engine.
(8) Measure the regular pressure.

ST1

925711000

PRESSURE GAUGE

ST2

34099AC020

ADAPTER HOSE B

ST3

34099AC010

ADAPTER HOSE A

Service limit:

981 kPa (10 kgf/cm

2

, 142 psi) or less

(9) If it is not within the specification, replace the
problem part for the following problems. (Pipe
or hose clogged, leaks from fluid line, and mix-
ture of foreign matter in fluid line)

2) Measure the relief pressure.

(1) Using the STs, measure the relief pressure.
(2) Close the valve.
(3) Measure the relief pressure.

ST1

925711000

PRESSURE GAUGE

ST2

34099AC020

ADAPTER HOSE B

ST3

34099AC010

ADAPTER HOSE A

Service limit:

Non-turbo model:

7,350 — 8,050 kPa 
(75 — 82 kgf/cm

2

, 1,066 — 1,167 psi)

Turbo model:

8,100 — 8,800 kPa 
(83 — 90 kgf/cm

2

, 1,174 — 1,276 psi)

(4) If it is not within the specification, replace the
oil pump.

(1) Suction hose

(2) Pressure hose

(1) Suction hose

(2) Pressure hose

PS-00688

(1)

(2)

PS-00459

(2)

(1)

(1) Valve

(1) Valve

PS-00152

PS-00153

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Бренд: Mercedes-Benz Страницы: 373
Thule 1308 Instructions Manual preview
1308
Бренд: Thule Страницы: 8
Phonocar 4/084 Mounting Instructions preview
4/084
Бренд: Phonocar Страницы: 2
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Бренд: Sumitomo Страницы: 22
Westin 22-1065 Instructions preview
22-1065
Бренд: Westin Страницы: 3
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Бренд: Weltmann KFZ-Teile Страницы: 12
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
ULTIMATE SPEED 285690 Assembly And Safety Advice preview
285690
Бренд: ULTIMATE SPEED Страницы: 10
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Бренд: FIRRAK Страницы: 12
Scosche VQ2M Manual preview
VQ2M
Бренд: Scosche Страницы: 32
Kargo Master 48132 Instruction Manual preview
48132
Бренд: Kargo Master Страницы: 9
Feniex QUAD QSM-8101 Manual preview
QUAD QSM-8101
Бренд: Feniex Страницы: 4
Curt Group Aries 2074113 Installation Manual preview
Aries 2074113
Бренд: Curt Group Страницы: 2
Haltech PLATINUM HT051202 Quick Start Manual preview
PLATINUM HT051202
Бренд: Haltech Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды