manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4SO)(diag)-77

Diagnostics for Engine Starting Failure

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK IGNITION SYSTEM FOR SPARKS.

1) Remove the plug cord cap from each spark 
plug.
2) Install a new spark plug on plug cord cap.

CAUTION:
Do not remove the spark plug from engine.

3) Contact the spark plug thread portion to 
engine.
4) While opening the throttle valve fully, crank 
the engine to check that spark occurs at each 
cylinder.

Does spark occur at each cylin-
der?

Check fuel pump 
system. <Ref. to 
EN(H4SO)(diag)-
79, FUEL PUMP 
CIRCUIT, Diag-
nostics for Engine 
Starting Failure.>

Go to step 

2

.

2

CHECK POWER SUPPLY CIRCUIT FOR IG-
NITION COIL AND IGNITOR ASSEMBLY.

1) Turn the ignition switch to OFF.
2) Disconnect the connector from the ignition 
coil and ignitor assembly.
3) Turn the ignition switch to ON.
4) Measure the voltage between ignition coil 
and ignitor assembly connector and engine 
ground.

Connector & terminal

(E12) No. 2 (+) — Engine ground (–):

Is the voltage 10 V or more?

Go to step 

3

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ignition coil and ig-
nitor assembly and
IG relay connector
• Poor contact of
coupling connector
• Blown out of fuse

3

CHECK HARNESS BETWEEN ECM AND IG-
NITION COIL AND IGNITOR ASSEMBLY.

1) Turn the ignition switch to OFF.
2) Measure the resistance between ECM and 
the ignition coil and ignitor assembly connector.

Connector & terminal

(E12) No. 3 — (B137) No. 6:
(E12) No. 3 — (B137) No. 26:

Is the resistance less than 1 

:

? Go to step 

4

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and ignition
coil and ignitor as-
sembly connector
• Poor contact of
coupling connector

4

CHECK IGNITION COIL AND IGNITOR AS-
SEMBLY.

1) Remove the spark plug cords.
2) Measure the resistance between spark plug 
cord contact portions to check secondary coil.

Terminals

No. 1 — No. 2:
No. 3 — No. 4:

Is the resistance between 10 and 
15 k

:

?

Go to step 

5

.

Replace the igni-
tion coil and ignitor 
assembly. <Ref. to 
IG(H4SO)-6, Igni-
tion Coil and Ignitor 
Assembly.>

5

CHECK INPUT SIGNAL FOR IGNITION COIL 
AND IGNITOR ASSEMBLY.

1) Connect the connector to the Ignition coil 
and ignitor assembly.
2) Check if voltage varies synchronously with 
engine speed when cranking, while monitoring 
voltage between ignition coil and ignitor assem-
bly connector and engine ground.

Connector & terminal

(E12) No. 1 (+) — Engine ground (–):
(E12) No. 4 (+) — Engine ground (–):

Does the voltage vary 10 V or 
more?

Go to step 

6

.

Replace the igni-
tion coil and ignitor 
assembly. <Ref. to 
IG(H4SO)-6, Igni-
tion Coil and Ignitor 
Assembly.>

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
RAM 2500 2020 Quick Reference Manual preview
2500 2020
Бренд: RAM Страницы: 20
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
PEUGEOT 407 2010 Manual preview
407 2010
Бренд: PEUGEOT Страницы: 249
Vauxhall Astra 2021 Owner'S Manual preview
Astra 2021
Бренд: Vauxhall Страницы: 259
WABCO Truck Training Model Operating Instructions Manual preview
Truck Training Model
Бренд: WABCO Страницы: 56
RAM RAM C 2013 Specification preview
RAM C 2013
Бренд: RAM Страницы: 5
Lock'er Down 2011 X Instructions preview
2011 X
Бренд: Lock'er Down Страницы: 2
Volvo V70 2014 Quick Manual preview
V70 2014
Бренд: Volvo Страницы: 16
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Бренд: T.J.M. Страницы: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Бренд: Audi Страницы: 4
DRAGONFIRE 11-0800 Installation Instructions preview
11-0800
Бренд: DRAGONFIRE Страницы: 4
Edelbrock PRO-FLO XT 3527 User Manual preview
PRO-FLO XT 3527
Бренд: Edelbrock Страницы: 39
Istar PI00670 Instruction Manual preview
PI00670
Бренд: Istar Страницы: 6
TATA Motors Indigo Marina Owner'S Manual & Service Book preview
Indigo Marina
Бренд: TATA Motors Страницы: 146

Бренды по названию

Популярные бренды

Загрузить еще бренды