manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4SO)(diag)-275

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

CY:DTC P2096 POST CATALYST FUEL TRIM SYSTEM TOO LEAN (BANK 1)

Refer to DTC P2097 for diagnostic procedure. <Ref. to EN(H4SO)(diag)-276, DTC P2097 POST CATALYST
FUEL TRIM SYSTEM TOO RICH (BANK 1), Diagnostic Procedure with Diagnostic Trouble Code (DTC).>

33

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL MO-
TOR.

1) Connect the connector to ECM.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic 
throttle control connector and engine ground.

Connector & terminal

(E57) No. 2 (+) — Engine ground (–):
(E57) No. 1 (+) — Engine ground (–):

Is the voltage 5 V or more?

Repair the short 
circuit to power in 
harness between 
ECM and elec-
tronic throttle con-
trol connector.

Go to step 

34

.

34

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL MO-
TOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM.
3) Measure the resistance between electronic 
throttle control connector and engine ground.

Connector & terminal

(E57) No. 2 — Engine ground:
(E57) No. 1 — Engine ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

35

.

Repair the short 
circuit to ground in 
harness between 
ECM and elec-
tronic throttle con-
trol connector.

35

CHECK ELECTRONIC THROTTLE CON-
TROL MOTOR HARNESS.

Measure the resistance between electronic 
throttle control connectors.

Connector & terminal

(E57) No. 2 — (E57) No. 1:

Is the resistance 1 M

:

 or 

more?

Go to step 

36

.

Repair the short 
circuit of harness 
between ECM and 
electronic throttle 
control connector.

36

CHECK ELECTRONIC THROTTLE CON-
TROL GROUND CIRCUIT.

Measure the resistance between ECM and 
chassis ground.

Connector & terminal

(B134) No. 5 — Chassis ground:
(B137) No. 1 — Chassis ground:
(B137) No. 2 — Chassis ground:
(B137) No. 3 — Chassis ground:
(B137) No. 7 — Chassis ground:

Is the resistance less than 5 

:

? Go to step 

37

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM and engine
ground
• Poor contact of
coupling connector

37

CHECK ELECTRONIC THROTTLE CON-
TROL.

Measure the resistance between electronic 
throttle control terminals.

Terminals

No. 2 — No. 1:

Is the resistance 50 

:

 or less? Go to step 

38

.

Replace the elec-
tronic throttle con-
trol. <Ref. to 
FU(H4SO)-14,
Throttle Body.>

38

CHECK ELECTRONIC THROTTLE CON-
TROL.

Move the throttle valve to the fully open and fully 
closed positions with fingers.
Check that the valve returns to the specified 
position when releasing fingers.

Does the valve return to the 
specified position?Standard 
value: 3 mm (0.12 in) from fully 
closed position

Repair the poor 
contact of ECM 
connector.

Replace the elec-
tronic throttle con-
trol. <Ref. to 
FU(H4SO)-14,
Throttle Body.>

Step

Check

Yes

No

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Cadillac SRX 2012 Instructions preview
SRX 2012
Бренд: Cadillac Страницы: 3
Cadillac Escalade 2021 Features Manual preview
Escalade 2021
Бренд: Cadillac Страницы: 12
Cadillac CTS 2008 Navigation System Owner'S Manual preview
CTS 2008
Бренд: Cadillac Страницы: 106
Cadillac CTS 2008 Customer Convenience/Personalization Manual preview
CTS 2008
Бренд: Cadillac Страницы: 20
Cadillac ATS 2014 Convenience/Personalization Manual preview
ATS 2014
Бренд: Cadillac Страницы: 20
Cadillac ATS 2013 Owner'S Manual preview
ATS 2013
Бренд: Cadillac Страницы: 326
Cadillac CTS 2012 Quick Manual preview
CTS 2012
Бренд: Cadillac Страницы: 28
Cadillac ESCALADE - BROCHURE 2009 Owner'S Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 602
Cadillac ESCALADE ESV 2004 Owner'S Manual preview
ESCALADE ESV 2004
Бренд: Cadillac Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды