manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4SO)(diag)-300

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL.

1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and 
electronic throttle control.
3) Measure the resistance between ECM and 
chassis ground.

Connector & terminal

(B134) No. 19 — Chassis ground:
(B134) No. 18 — Chassis ground:
(B134) No. 18 — (B136) No. 6:
(B134) No. 28 — Chassis ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

2

.

Repair the short 
circuit to ground in 
harness between 
ECM and elec-
tronic throttle con-
trol connector.

2

CHECK SHORT CIRCUIT INSIDE THE ECM.

1) Connect the connector to ECM.
2) Measure the resistance between electronic 
throttle control connector and engine ground.

Connector & terminal

(E57) No. 6 — Engine ground:
(E57) No. 4 — Engine ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

3

.

Repair the short 
circuit to ground in 
harness between 
ECM and elec-
tronic throttle con-
trol connector. 
Replace the ECM if 
defective. <Ref. to 
FU(H4SO)-45,
Engine Control 
Module (ECM).>

3

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL.

1) Disconnect the connectors from ECM.
2) Measure the resistance of harness between 
ECM and electronic throttle control connector.

Connector & terminal

(B134) No. 18 — (E57) No. 6:
(B134) No. 28 — (E57) No. 4:
(B134) No. 29 — (E57) No. 3:

Is the resistance less than 1 

:

? Go to step 

4

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and electron-
ic throttle control
connector
• Poor contact of
coupling connector

4

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL.

1) Connect the connector to ECM.
2) Measure the resistance between electronic 
throttle control connector and engine ground.

Connector & terminal

(E57) No. 3 — Engine ground:

Is the resistance less than 5 

:

? Go to step 

5

.

Repair the harness 
and connector.
NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
ECM and engine
ground
• Poor contact of
ECM connector
• Poor contact of
coupling connector

5

CHECK HARNESS BETWEEN ECM AND 
ELECTRONIC THROTTLE CONTROL.

1) Turn the ignition switch to ON.
2) Measure the voltage between electronic 
throttle control connector and engine ground.

Connector & terminal

(E57) No. 6 (+) — Engine ground (–):
(E57) No. 4 (+) — Engine ground (–):

Is the voltage 4.85 V or more? Repair the short 

circuit to power in 
harness between 
ECM and elec-
tronic throttle con-
trol connector.

Go to step 

6

.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Davis Instruments 8127 Installation Instructions Manual preview
8127
Бренд: Davis Instruments Страницы: 16
Yakima K343 Manual preview
K343
Бренд: Yakima Страницы: 11
LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
Vaisala MD30 Setup Manual preview
MD30
Бренд: Vaisala Страницы: 24
Warrior Winches C10000NH Assembly & Operating Instructions preview
C10000NH
Бренд: Warrior Winches Страницы: 17
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Air Lift WirelessAIR 73000EZ Manual preview
WirelessAIR 73000EZ
Бренд: Air Lift Страницы: 12
Lexus LX 470 Owner'S Manual preview
LX 470
Бренд: Lexus Страницы: 369
Mountain Top Sports Bar Installation Manual preview
Sports Bar
Бренд: Mountain Top Страницы: 12
Alfa Romeo Alfa 147 Quick Start Manual preview
Alfa 147
Бренд: Alfa Romeo Страницы: 8
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Бренд: Yakima Страницы: 11
RAM Truck Diesel Supplement 2012 Owner'S Manual preview
Truck Diesel Supplement 2012
Бренд: RAM Страницы: 174
Yutrax TX107 Operator'S Manual preview
TX107
Бренд: Yutrax Страницы: 8
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
POOL-LINE 110050 Assembly Instructions preview
110050
Бренд: POOL-LINE Страницы: 2
BMW M3 SEDAN Owner'S Manual preview
M3 SEDAN
Бренд: BMW Страницы: 392

Бренды по названию

Популярные бренды

Загрузить еще бренды