manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

4AT-48

Inhibitor Switch

AUTOMATIC TRANSMISSION

13.Inhibitor Switch

A: INSPECTION

When the driving condition or starter motor opera-
tion is improper, first check the shift linkage for im-
proper operation. If the shift linkage is functioning
properly, check the inhibitor switch.
1) Disconnect the inhibitor switch connector.
2) Check continuity in inhibitor switch circuits with
the select lever moved to each position.

NOTE:
• Also check that there is no continuity in the igni-
tion circuit when the select lever is in the “R” and
“D” ranges.
• If the inhibitor switch does not operate, check for
poor contact of the connector on transmission side.

3) Check that there is continuity at equal points
when the select lever is moved 1.5° in both direc-
tions from the “N” range.
If there is continuity in only one direction or in other
points, adjust the inhibitor switch. <Ref. to 4AT-48,
ADJUSTMENT, Inhibitor Switch.>

4) Repeat the above inspection in other gear rang-
es. If there are abnormalities, adjust the select ca-
ble. <Ref. to CS-27, ADJUSTMENT, Select
Cable.>

B: ADJUSTMENT

1) Set the select lever to “N” range.
2) Loosen the two bolts holding the inhibitor switch.
3) Insert the ST as vertical as possible into the
holes of the shifter arm and switch body.
ST

499267300

STOPPER PIN

4) Tighten the two bolts holding the inhibitor switch.

Tightening torque:

5 N·m (0.5 kgf-m, 3.7 ft-lb)

5) Repeat the inspection of the inhibitor switch. If
the inhibitor switch is determined to be “faulty”, re-
place it.

Signal sent to TCM

Range

Pin No.

P

4  —  3

R

4  —  2

N

4  —  1

D

4  —  8

Ignition circuit

P/N

12 — 11

Back-up light circuit

R

10 — 9

(A) Inhibitor switch connector

AT-00030

( 4 ) ( 3 ) ( 2 ) ( 1 )

( 5 )

( 6 )

( 7 )

( 8 )

( 9 )

(10)

(11)

(12)

(A)

(A) Continuity does not exist.

(B) Continuity exists.

(C) 1.5°

AT-04578

(A)

(A)

(C)

(B)

AT-04866

S T

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Бренд: TATA Motors Страницы: 94
GÄN GA Manual preview
GA
Бренд: GÄN Страницы: 24
iArmor IA-N179 Manual preview
IA-N179
Бренд: iArmor Страницы: 6
Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Бренд: Quadratec Страницы: 6
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Бренд: FORM FIT Страницы: 2
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
kincrome K12071 Owner'S Assemble And Operating Manual preview
K12071
Бренд: kincrome Страницы: 6
Mazda 2008 MX-5 Miata Manual preview
2008 MX-5 Miata
Бренд: Mazda Страницы: 400
muth signal mirror Instalation Instructions preview
signal mirror
Бренд: muth Страницы: 10
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Mercedes-Benz R 350 2012 Operator'S Manual preview
R 350 2012
Бренд: Mercedes-Benz Страницы: 368
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Бренд: Mercedes-Benz Страницы: 91
Xpresskit DBALL2-HK7 Installation Manual preview
DBALL2-HK7
Бренд: Xpresskit Страницы: 18
Thule 1061-1-011 Fitting Instructions preview
1061-1-011
Бренд: Thule Страницы: 3
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Бренд: FALCON RIDGE Страницы: 4
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Бренд: INDIWORK Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды