manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

WI-3

Basic Diagnostic Procedure

WIRING SYSTEM

1. Basic Diagnostic Procedure

A: BASIC PROCEDURES

1. GENERAL DESCRIPTION

The most important purpose of diagnostics is to
quickly determine which part is malfunctioning, to
save time and labor.

2. IDENTIFICATION OF TROUBLE SYMPTOM

Determine what the problem is based on the symp-
tom.

3. PROBABLE CAUSE OF TROUBLE

Look at the wiring diagram and check the system’s
circuit. Then check the switch, relay, fuse, ground,
etc.

4. LOCATION AND REPAIR OF TROUBLE

1) Using the diagnostics, narrow down the causes.
2) If necessary, use a voltmeter, ohmmeter, etc.
3) Before replacing certain component parts
(switch, relay, etc.), check the power supply,
ground, for open wiring harness, poor connectors,
etc. If no problem is encountered, check the com-
ponent parts.

5. SYSTEM OPERATION CHECK

After repairing, ensure that the system operates
properly.

B: BASIC INSPECTION

1. VOLTAGE MEASUREMENT

1) Using a voltmeter, connect the negative lead to a
good ground point or negative battery terminal and
the positive lead to the connector or component ter-
minal.
2) Touch connector (A) with the positive probe of
the volt meter. The voltmeter will indicate a voltage.
3) Touch connector (B) with the positive probe. The
voltmeter will indicate no voltage.

4) With the test set-up held as it is, turn the switch
to ON. The voltmeter will indicate a voltage and, at
the same time, the light will illuminate.
5) The circuit is in good order. If a problem such as
a light failing to illuminate occurs, use the proce-
dures outlined above to track down the malfunc-
tion.

2. CIRCUIT CONTINUITY CHECKS

1) Disconnect the battery terminal or connector so
there is no voltage between the check points.
Contact the two leads of an ohmmeter to each of
the check points.
If the circuit has diodes, reverse the two leads and
check again.
2) Use an ohmmeter to check for diode continuity.
When contacting the negative lead to the diode
positive side and the positive lead to the negative
side, there should be continuity.
When contacting the two leads in reverse, there
should be no continuity.

To power

Fuse

supply

Switch

Light

V

(A)

(B)

WI-02739

Continuity  

No continuity

WI-02740

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
Falcon 1990 Installation Instructions And Specifications preview
1990
Бренд: Falcon Страницы: 8
Garmin BC 30 Owner'S Manual preview
BC 30
Бренд: Garmin Страницы: 2
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Бренд: Kolpin Страницы: 25
Alpine eX-10 Owner'S Manual preview
eX-10
Бренд: Alpine Страницы: 69
Allen Sports S302 Instructions preview
S302
Бренд: Allen Sports Страницы: 2
Thule 1511 Instructions Manual preview
1511
Бренд: Thule Страницы: 8
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Бренд: Cadillac Страницы: 368
Luverne 205760 Installation Instructions preview
205760
Бренд: Luverne Страницы: 3
Navman B2+ User Manual preview
B2+
Бренд: Navman Страницы: 27
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Бренд: VER-MAC Страницы: 64
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Бренд: Dodge Страницы: 293
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Бренд: ULTIMATE SPEED Страницы: 40
NavInc CP-PEU-GV3 Manual preview
CP-PEU-GV3
Бренд: NavInc Страницы: 6
E&G Classics Denali 1094-0185-15 Instruction Manual preview
Denali 1094-0185-15
Бренд: E&G Classics Страницы: 3
Metra Electronics 99-7803G Wiring Instructions preview
99-7803G
Бренд: Metra Electronics Страницы: 2
v.link VL2-DVD900 Manual preview
VL2-DVD900
Бренд: v.link Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды