manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

TPM(diag)-3

General Description

TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS)

2. General Description

A: CAUTION

1. SUPPLEMENTAL RESTRAINT SYSTEM 
“AIRBAG”

Airbag system wiring harness is routed near the
TPM control module.

CAUTION:
• All airbag system wiring harnesses are yel-
low. Do not use the electrical test equipment on
these circuits.
• Be careful not to damage the airbag system
wiring harness when servicing the tire pressure
monitoring control module.

2. TIRE PRESSURE MONITORING 
CONTROL MODULE

• If the transmitter is replaced, ID registration for
the transmitter is required. <Ref. to TPM(diag)-10,
REGISTER TRANSMITTER ID, OPERATION,
Subaru Select Monitor.>
• When adjusting tire pressure indoors in winter,
there is a big temperature difference between the
indoor facilities and outside. Once the car is outside
where the temperature is lower, the air pressure in
the tires will drop, causing the tire pressure warning
light to illuminate, even if the pressure in the tires
was adjusted to standard values indoors. To avoid
this, it is necessary to adjust the tire pressure to the
high side in consideration of the difference in tem-
perature between inside and outside according to
the following table.

P205/50R17 and P205/55R16

B: INSPECTION

Before performing diagnosis, check the following
item which might affect the quality of the tire pres-
sure monitoring system.

1. TIRE

• Inspect that the tire pressure is within the speci-
fication while the tire is cool. (Refer to Tire Caution
Label.)
• Check the tires for damage or the insertion of for-
eign matters.

2. BATTERY

Check that amount of battery fluid, gravity and volt-
age are within the specifications.

Standard voltage: 12 V or more

Specific gravity: 1.260 or more

Tempera-

ture

°C (°F)

Indoor 

temperature

15.5 (60)

Ambient 

temperature

–1 (30)

–12 (10)

–23 (–10)

Air

pressure
kPa (psi)

Front

250 (36)

265 (38)

280 (40)

Rear

240 (35)

255 (37)

270 (39)

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Yakima SideWinder Installation Instructions And Owner'S Manual preview
SideWinder
Бренд: Yakima Страницы: 8
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 4
Chevrolet Avalanche 2005 Owner'S Manual preview
Avalanche 2005
Бренд: Chevrolet Страницы: 494
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Бренд: Metra Electronics Страницы: 8
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Бренд: Safe Fleet Страницы: 24
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Бренд: ULTIMATE SPEED Страницы: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Бренд: Chevrolet Страницы: 441
ULTIMATE SPEED 91449 Operation And Safety Notes preview
91449
Бренд: ULTIMATE SPEED Страницы: 34
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Бренд: Oldsmobile Страницы: 340
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Бренд: Volvo Страницы: 166
Pogo Alert+ Operating Instructions Manual preview
Alert+
Бренд: Pogo Страницы: 40
Axxess AXGMLN-09 Installation Instructions preview
AXGMLN-09
Бренд: Axxess Страницы: 4
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Бренд: Charge Amps Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды