Subaru 2009 IMPREZA Скачать руководство пользователя страница 1272

Страница: 1272 / 3619

EN(H4DOTC)(diag)-51

Drive Cycle

ENGINE (DIAGNOSTICS)

4. DRIVE CYCLE C — DRIVE THE VEHICLE WITH FOLLOWING DRIVE PATTERNS

(A)

Idle the engine for 10 seconds or
more.

(D)

Decelerate with fully closed
throttle to 64 km/h (40 MPH).

(G)

Stop the vehicle with throttle fully
closed.

(B)

Accelerate to 97 km/h (60 MPH)
within 20 seconds.

(E)

Drive the vehicle at 64 km/h
(40 MPH) for 20 seconds.

(H)

Vehicle speed km/h (MPH)

(I)

Sec.

(C)

Drive the vehicle at 97 km/h
(60 MPH) for 20 seconds.

(F)

Accelerate to 97 km/h (60 MPH)
within 10 seconds.

DTC

Item

Condition

*P0030

HO2S Heater Control Circuit (Bank 1 Sensor 1)

—

*P0068

MAP/MAF - Throttle Position Correlation

—

*P0101

Mass or Volume Air Flow Circuit Range/Performance

—

P0134

O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)

—

*P0139

O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)

—

*P0171

System Too Lean (Bank 1)

Complete diagnosis with drive cycle A or B as well.

*P0172

System Too Rich (Bank 1)

Complete diagnosis with drive cycle A or B as well.

P0244

Turbo/Super Charger Wastegate Solenoid “A” Range/Performance

—

P0246

Turbo/Super Charger Wastegate Solenoid “A” High

—

*P0301

Cylinder 1 Misfire Detected

Complete diagnosis with drive cycle A or B as well.

*P0302

Cylinder 2 Misfire Detected

Complete diagnosis with drive cycle A or B as well.

*P0303

Cylinder 3 Misfire Detected

Complete diagnosis with drive cycle A or B as well.

*P0304

Cylinder 4 Misfire Detected

Complete diagnosis with drive cycle A or B as well.

P2004

Intake Manifold Runner Control Stuck Open (Bank 1)

—

P2005

Intake Manifold Runner Control Stuck Open (Bank 2)

—

*P2096

Post Catalyst Fuel Trim System Too Lean (Bank 1)

Complete diagnosis with drive cycle A or B as well.

*P2097

Post Catalyst Fuel Trim System Too Rich (Bank 1)

Complete diagnosis with drive cycle A or B as well.

EN-00842

(C)

(H)

(I)

(60)

64 (40)

(B)

(A)

(F)

(D)

(E)

150

100

(G)

«
...
1270
1271
1272
1273
1274
...
»

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 2009 IMPREZA

Отзывы:

Похожие инструкции для 2009 IMPREZA

Бренды по названию

Популярные бренды

Subaru 2009 IMPREZA, Руководство по обслуживанию

Результаты поиска

Содержание 2009 IMPREZA

Отзывы:

Похожие инструкции для 2009 IMPREZA

Бренды по названию

Популярные бренды