manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

VDC(diag)-47

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS)

Step

Check

Yes

No

1

WHETHER A WHEEL TURNED FREELY OR 
NOT.

Check if the wheels have been turned freely for 
one minute or more, such as when the vehicle is 
jacked-up, under full-lock cornering or when the 
wheels are not in contact with road surface.

Did the wheels turn freely?

VDC is normal. 
Clear the memory.

NOTE:
This diagnostic
trouble code may
sometimes occur if
the wheels turn
freely for a long
time, for example
when the vehicle is
towed or jacked-
up, or when steer-
ing wheel is contin-
uously turned all
the way.

Go to step 

2

.

2

CHECK TIRE SPECIFICATIONS.

Turn the ignition switch to OFF.

Are the tire specifications cor-
rect?

Go to step 

3

.

Replace the tire.

3

CHECK WEAR OF TIRE.

Is the tire worn excessively?

Replace the tire.

Go to step 

4

.

4

CHECK TIRE INFLATION PRESSURE.

Is the tire pressure correct?

Go to step 

5

.

Adjust the tire 
pressure.

5

CHECK INSTALLATION OF ABS WHEEL 
SPEED SENSOR.

Are the ABS wheel speed sen-
sor installation bolts tightened 
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)? 
(For four wheels)

Go to step 

6

.

Tighten the ABS 
wheel speed sen-
sor installation 
bolts.

6

CHECK ABS WHEEL SPEED SENSOR SIG-
NAL.

1) Install the ABS wheel speed sensor.
2) Prepare an oscilloscope.
3) Check the ABS wheel speed sensor. <Ref. 
to ABS-14, ABS WHEEL SPEED SENSOR, 
INSPECTION, Front ABS Wheel Speed Sen-
sor.>

Does the oscilloscope indicate 
the waveform pattern like 
shown in the figure when the 
tire is slowly turned? Does the 
oscilloscope indication repeat 
the waveform pattern like 
shown in the figure when the 
tire is slowly turned in equal 
speed for one rotation or more?

Go to step 

8

.

Go to step 

7

.

7

CHECK ABS WHEEL SPEED SENSOR OR 
MAGNETIC ENCODER.

Are there foreign matter, break-
age or damage at the tip of ABS 
wheel speed sensor or mag-
netic encoder?

Remove dirt thor-
oughly. Also 
replace the ABS 
wheel speed sen-
sor or magnetic 
encoder as a unit 
with hub unit bear-
ing if it is broken or 
damaged.

Go to step 

8

.

8

CHECK VDCCM&H/U.

1) Connect all connectors.
2) Clear the memory. <Ref. to VDC(diag)-24, 
Clear Memory Mode.>
3) Perform the Inspection Mode. <Ref. to 
VDC(diag)-23, Inspection Mode.>
4) Read the DTC.

Is the same DTC displayed?

Replace the 
VDCCM only. 
<Ref. to VDC-9, 
REPLACEMENT, 
VDC Control Mod-
ule and Hydraulic 
Control Unit 
(VDCCM&H/U).>

Go to step 

9

.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Бренд: CITROEN Страницы: 2
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Gator GX5HDKT User Manual preview
GX5HDKT
Бренд: Gator Страницы: 8
Chevrolet 1999 Malibu Owner'S Manual preview
1999 Malibu
Бренд: Chevrolet Страницы: 344
Prorack K692 Fitting Instructions Manual preview
K692
Бренд: Prorack Страницы: 15
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Бренд: Nuna Страницы: 17
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Бренд: Ranger design Страницы: 24
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Бренд: Dodge Страницы: 293
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Бренд: Demco Страницы: 4
Streetwize SWGH3 Quick Start Manual preview
SWGH3
Бренд: Streetwize Страницы: 4
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
Cadillac 2001 Eldorado Owner'S Manual preview
2001 Eldorado
Бренд: Cadillac Страницы: 335
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Бренд: Menabo Страницы: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Бренд: Seat Страницы: 372
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Бренд: Metra Electronics Страницы: 10
Honda Vezel Owner'S Manual preview
Vezel
Бренд: Honda Страницы: 279

Бренды по названию

Популярные бренды

Загрузить еще бренды