manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

EN(H4DOTC)(diag)-219

Diagnostic Procedure with Diagnostic Trouble Code (DTC)

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK FUEL FILLER CAP.

1) Turn the ignition switch to OFF.
2) Check the fuel filler cap.
NOTE:
The DTC is stored in memory if fuel filler cap is
or was loose or if the cap chain has caught while
tightening.

Is the fuel filler cap tightened 
securely?

Go to step 

2

.

Tighten fuel filler 
cap securely.

2

CHECK FUEL FILLER CAP.

Is the fuel filler cap genuine?

Go to step 

3

.

Replace with a 
genuine fuel filler 
cap.

3

CHECK FUEL FILLER PIPE GASKET.

Is there any damage to the seal 
between fuel filler cap and fuel 
filler pipe?

Repair or replace 
the fuel filler cap 
and fuel filler pipe. 
<Ref. to 
FU(H4DOTC)-69, 
Fuel Filler Pipe.>

Go to step 

4

.

4

CHECK DRAIN VALVE.

1) Connect the delivery (test) mode connector.
2) Turn the ignition switch to ON.
3) Operate the drain valve using the Subaru 
Select Monitor.
NOTE:
The drain valve can be operated using Subaru
Select Monitor. For the procedures, refer to
“Compulsory Valve Operation Check Mode”.
<Ref. to EN(H4DOTC)(diag)-55, Compulsory
Valve Operation Check Mode.>

Does the drain valve operate?

Go to step 

5

.

Replace the drain 
valve. <Ref. to 
EC(H4DOTC)-22, 
Drain Valve.>

5

CHECK PURGE CONTROL SOLENOID 
VALVE.

Operate the purge control solenoid valve using 
the Subaru Select Monitor.
NOTE:
Purge control solenoid valve operation can be
executed using Subaru Select Monitor. For the
procedures, refer to “Compulsory Valve Opera-
tion Check Mode”. <Ref. to EN(H4DOTC)(di-
ag)-55, Compulsory Valve Operation Check
Mode.>

Does the purge control sole-
noid valve operate?

Go to step 

6

.

Replace the purge 
control solenoid 
valve. <Ref. to 
EC(H4DOTC)-11, 
Purge Control 
Solenoid Valve.>

6

CHECK PRESSURE CONTROL SOLENOID 
VALVE.

Operate the pressure control solenoid valve 
using the Subaru Select Monitor.
NOTE:
The pressure control solenoid valve operation
can be executed using the Subaru Select Mon-
itor. For the procedures, refer to “Compulsory
Valve Operation Check Mode”. <Ref. to
EN(H4DOTC)(diag)-55, Compulsory Valve Op-
eration Check Mode.>

Does the pressure control sole-
noid valve operate?

Go to step 

7

.

Replace the pres-
sure control sole-
noid valve. <Ref. to 
EC(H4DOTC)-19, 
Pressure Control 
Solenoid Valve.>

7

CHECK EVAPORATIVE EMISSION CON-
TROL SYSTEM LINE.

1) Turn the ignition switch to OFF.
2) Disconnect the delivery (test) mode connec-
tor.

Is there any hole of more than 
1.0 mm (0.04 in) dia. on evapo-
ration line?

Repair or replace 
the evaporation 
line. <Ref. to 
FU(H4DOTC)-84, 
Fuel Delivery, 
Return and Evapo-
ration Lines.>

Go to step 

8

.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Carcomm CNM-71 Quick Start Manual preview
CNM-71
Бренд: Carcomm Страницы: 2
Whispbar K392W Fitting Instructions For Basic Carrier preview
K392W
Бренд: Whispbar Страницы: 14
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Бренд: Atwood Страницы: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Бренд: BMW Страницы: 21
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
Oldsmobile 2004 Alero Quick Manual preview
2004 Alero
Бренд: Oldsmobile Страницы: 2
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Бренд: PAC Страницы: 14
Kolpin 98310 Product Instructions preview
98310
Бренд: Kolpin Страницы: 3
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
PUTCO 1951 Series Instruction Manual preview
1951 Series
Бренд: PUTCO Страницы: 3
Kolpin 1466 Product Instructions preview
1466
Бренд: Kolpin Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды