Subaru 2009 IMPREZA Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 3619

background image

PM-39

Suspension

PERIODIC MAINTENANCE SERVICES

21.Suspension

A: INSPECTION

1. SUSPENSION BALL JOINT

1) Jack-up the vehicle until front wheels are off
ground.
2) Grasp the bottom of tire and move it in and out in
axial direction. If relative movement (B) is observed
between the brake disc cover (A) and the end of
front arm (D), ball joint (C) may be excessively
worn.

3) Grasp the end of front arm and move it up and
down. Relative movement (A) between the housing
(D) and front arm (C) boss indicates ball joint (B)
may be excessively worn.

4) If the relative movement is observed in the pre-
ceding two steps, remove and inspect the ball joint.
If the free play exceeds the standard, replace the
ball joint. <Ref. to FS-17, Front Ball Joint.>

5) Damage of dust boots
Visually inspect the ball joint dust boots. If it is dam-
aged, remove the front arm. <Ref. to FS-19, Front
Arm.> Measure the play of the ball point. <Ref. to
FS-17, Front Ball Joint.>

(1) When looseness exceeds the standard, re-
place the ball joint.
(2) If the dust boots are damaged, replace with
a new ball joint.

NOTE:
When the front arm ball joint has been removed or
replaced, check the toe of front wheel. If the front
wheel toe-in is not at specified value, adjust the
toe-in. <Ref. to FS-7, Wheel Alignment.>

2. FRONT, REAR SUSPENSION BUSHING

Apply pressure with tire lever etc. to inspect the
bushing for fatigue or cracks. If defective, replace
the bushing.

(D)

(C)

(A)

(B)

PM-00258

(D)

(C)

(B)

(A)

PM-00259

(A) Dust boots

(A)

PM-00059

PM-00405

«
...
101
102
103
104
105
...
»

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Бренд: Westin Страницы: 3

Бренд: Lincoln Страницы: 424

Бренд: Volkswagen Страницы: 26

CHASSIS CAB 3500 2017

Бренд: RAM Страницы: 16

Sterling ALL-TERRAIN 576

Бренд: Roadmaster Страницы: 12

Бренд: PullRite Страницы: 10

Бренд: B-Speech Страницы: 24

Бренд: Alfa Romeo Страницы: 8

Бренд: CTEK Страницы: 84

Бренд: Kargo Master Страницы: 19

PRIME DESIGN VBR3-FT31B

Бренд: Safe Fleet Страницы: 12

Parktronic system Volkswagen Golf MK7

Бренд: Car-Systems Страницы: 10

Бренд: Cadillac Страницы: 20

Бренд: Kia Страницы: 680

Бренд: Cadillac Страницы: 335

Бренд: Brodit Страницы: 2

WG Grand Cherokee 2002

Бренд: Jeep Страницы: 74

Бренд: Hyundai Страницы: 380

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды