manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

ME(H4DOTC)-13

General Description

MECHANICAL

C: CAUTION

• Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing
any work.
• Remove contamination including dirt and corrosion before removal, installation or disassembly.
• Keep the disassembled parts in order and protect them from dust and dirt.
• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary removal, in-
stallation, disassembly and replacement.
• Vehicle components are extremely hot after driving. Be wary of receiving burns from heated parts.
• Be sure to tighten fasteners including bolts and nuts to the specified torque.
• Place shop jacks or rigid racks at the specified points.
• Before disconnecting connectors of sensors or units, be sure to disconnect the ground cable from the bat-
tery.
• All parts should be thoroughly cleaned, paying special attention to engine oil passages, pistons and bear-
ings.
• Rotating parts and sliding parts such as piston, bearing and gear should be coated with oil prior to assem-
bly.
• Be careful not to let oil, grease or engine coolant contact the timing belt, clutch disc and flywheel.
• All removed parts, if to be reused, should be reinstalled in the original positions and directions.
• Bolts, nuts and washers should be replaced with new parts as required.
• Even if necessary inspections have been made in advance, proceed with assembly work while making re-
checks.
• Remove or install the engine in an area where chain hoists, lifting devices, etc. are available for ready use.
• Be sure not to damage coated surfaces of body panels with tools, or not to stain seats and windows with
coolant or oil. Place a cover over fender, as required, for protection.
• Prior to starting work, prepare the following:
Service tools, clean cloth, containers to catch coolant and oil, wire ropes, chain hoist, transmission jacks, etc.
• Lift up or lower the vehicle when necessary. Make sure to support the correct positions.

D: PREPARATION TOOL

1. SPECIAL TOOL

ILLUSTRATION

TOOL NUMBER

DESCRIPTION

REMARKS

498267600

CYLINDER HEAD 
TABLE

• Used for replacing valve guides.
• Used for removing and installing valve spring.

498277200

STOPPER SET

Used for installing automatic transmission 
assembly to engine.

ST-498267600

ST-498277200

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

PAC RadioPRO 5 RP5-GM41 Quick Start Manual preview
RadioPRO 5 RP5-GM41
Бренд: PAC Страницы: 3
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 20
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Бренд: Kia Страницы: 419
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Бренд: Hyundai Страницы: 280
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
Chevrolet Impala Limited 2014 Owner'S Manual preview
Impala Limited 2014
Бренд: Chevrolet Страницы: 356
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12
Renault KANGOO BE BOP Driver'S Handbook Manual preview
KANGOO BE BOP
Бренд: Renault Страницы: 198
Fiat 500L 2020 Owner'S Manual preview
500L 2020
Бренд: Fiat Страницы: 284
Chevrolet 1995 C/K Pickup Owner'S Manual preview
1995 C/K Pickup
Бренд: Chevrolet Страницы: 483
HOLDEN Malibu EM 2015 Owner'S Handbook Manual preview
Malibu EM 2015
Бренд: HOLDEN Страницы: 330
ROLEC WallPod Series Installation Instructions preview
WallPod Series
Бренд: ROLEC Страницы: 2
Chrysler Sebring Convertible Owner'S Manual preview
Sebring Convertible
Бренд: Chrysler Страницы: 454

Бренды по названию

Популярные бренды

Загрузить еще бренды