manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

PI-2

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

1. Pre-delivery Inspection

A: GENERAL DESCRIPTION

The purposes of the pre-delivery inspection (PDI) are as follows.
• Remove the additional parts used for ensuring the vehicle quality during transportation and restore the ve-
hicle to its normal condition.
• Check the vehicle before delivery is in normal condition.
• Check the vehicle or parts for any damage occurred during transportation or storage.
• Check the vehicle after repair is in normal condition.
• Make sure to provide a complete vehicle to customer.
For above reasons, all SOAs (dealerships) must carry out the PDIs before delivery of vehicle.
Refer to this manual unless otherwise specified.

B: PRE-DELIVERY INSPECTION (PDI) PROCEDURE

Perform the procedures indicated in the table below.

Static Checks Just After Vehicle Receipt

Operation

Check point

1. Appearance

1. If the vehicle is covered with protective coating, visually check the vehicle 
body for damage and dents. If the protective coating has been removed, 
visually check the painted body surfaces in detail for damage or rust.
2. Visually check the glass and light lenses for any damage, cracks or exces-
sive gaps between body sheet metal.
3. Visually check the plated parts for any damage.
4. Check the instrument panel, console and trim for stains or dirt.

2. Tire

1. Check the tires for damage, defective, and dents on wheels.
2. Check the tire air pressure.

3. Fuse installation

If the vehicle is about to be delivered to customer, attach the room lamp fuse.

4. Door lock/unlock and open/close operations

1. Using the key, check the door can be locked or unlocked normally.
2. Open and close all doors to check that there are no problems.
3. Operate the power door lock switch to check that the rear gate locks and 
unlocks normally.

5. Child safety lock

Check the child safety lock system operates normally.

6. Trunk lid open/close operations

1. Using the key, check that the trunk lid can be locked or unlocked normally.
2. Operate the trunk lock release lever to check that the trunk lid opens normally.
3. Use the valet key to check that the lock cannot be released.
4. Open and close the trunk lid to check that there are no problems.

7. Rear gate lock/unlock and open/close operation 1. Check if the rear gate can be unlocked normally through the emergency hole.

2. Open and close the rear gate to check that there are no problems.

8. Operation check of trunk lid release lever

Operate the trunk lid release lever to check that the trunk lock is unlocked 
normally.

9. Fuel lid opener lock release lever

Operate the fuel lid opener to check that the fuel filler lid can be unlocked 
normally.

10. Accessory

Check that the following accessories are equipped.
• Owner’s  manual
• Warranty booklet
• Maintenance note
• Spare key
• Key No. plate
• Jack
• Tool set
• Spare tire
• Towing hook

11. Front hood lock release

Operate the front hood lock release lever to check that the front hood opens 
normally.

12. Battery

Check the battery for any abnormal conditions such as rust or traces of bat-
tery fluid leaks.

13. Brake fluid

Check the brake fluid amount.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
3SIXT 3S-1186 Operating Instructions Manual preview
3S-1186
Бренд: 3SIXT Страницы: 12
Ford Windstar 2003 Quick Reference Manual preview
Windstar 2003
Бренд: Ford Страницы: 2
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Бренд: Wilco Offroad Страницы: 4
Atera 022 681 Manual preview
022 681
Бренд: Atera Страницы: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Бренд: RAM Страницы: 7
AEM 30-3500 Instruction Manual preview
30-3500
Бренд: AEM Страницы: 27
Alfa Romeo 1966 Spider 105 Faq preview
1966 Spider 105
Бренд: Alfa Romeo Страницы: 46
Saab 2006 9-5 Owner'S Manual preview
2006 9-5
Бренд: Saab Страницы: 288
Dodge CHALLENGER HELLCAT 2017 Owner'S Manual preview
CHALLENGER HELLCAT 2017
Бренд: Dodge Страницы: 484
Mercedes-Benz W211 Manual preview
W211
Бренд: Mercedes-Benz Страницы: 27
HUSKY LINERS 47954 Installation Instructions preview
47954
Бренд: HUSKY LINERS Страницы: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Бренд: iOttie Страницы: 19
RADICAL R-C10AD2 Device Installation Manual preview
R-C10AD2
Бренд: RADICAL Страницы: 11
MovaNext Bike adapter 3 Assembly Instructions preview
Bike adapter 3
Бренд: MovaNext Страницы: 4
Lancia DELTA HF integrale Workshop Manual preview
DELTA HF integrale
Бренд: Lancia Страницы: 101
Safe Fleet PRIME DESIGN HRR-NV11B Manual preview
PRIME DESIGN HRR-NV11B
Бренд: Safe Fleet Страницы: 12
Honda 1996 Civic Del Sol Owner'S Manual preview
1996 Civic Del Sol
Бренд: Honda Страницы: 219

Бренды по названию

Популярные бренды

Загрузить еще бренды