manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

PS-52

General Diagnostic Table

POWER ASSISTED SYSTEM (POWER STEERING)

1. NOISE AND VIBRATION

CAUTION:
Do not keep the relief valve operated for five seconds or more at any time or inner parts of the oil
pump may be damaged due to rapid increase of fluid temperature.

NOTE:
• A screeching noise may be heard immediately after the engine start in extremely cold conditions. In this
case, if the noise goes off during warm-up there is no abnormal function in the system. This is due to the fluid
characteristics in extremely cold condition.
• The oil pump normally makes a small whining noise due to its mechanism. Even if a noise is heard when
steering wheel is turned at stand still, there is no abnormal function in the system provided that the noise
eliminates when the vehicle is driving.
• When turning the steering wheel with the brake applied when the vehicle is parked, a screeching noise
may be generated by the brake disc and pads. This is not a fault in the steering system.
• There may be a small vibration around the steering devices when turning the steering wheel at standstill,
even though the component parts are operating properly.
Hydraulic systems are likely to generate this kind of vibration as well as working noise and fluid noise be-
cause of combined conditions, i.e., road surface and tire surface, engine speed and turning speed of steering
wheel, fluid temperature and braking condition.
These conditions do not indicate a problem in the system.
Confirm vibration for an AT model, by applying the parking brake on a concrete surface, shifting into the “D”
range, and turning the steering wheel repeatedly from slow to rapid, step by step.

Trouble

Possible cause

Corrective action

Hiss noise (continuous)
While engine is running.

Relief valve emits operating sound when steering wheel is 
completely turned in either direction. (Do not keep this con-
dition for 5 seconds or more.)

Normal operation

Relief valve emits operating sound when steering wheel is 
not turned. This means that the relief valve is defective.

Replace the oil pump.

Rattling noise (intermittent)
While engine is running.

Interference with adjacent parts

Check the clearance.
Correct if necessary.
<Ref. to PS-56, INSPECTION OF 
CLEARANCE, INSPECTION, 
General Diagnostic Table.>

Loosened installation of oil pump, oil tank, pump bracket, 
gearbox or crossmember

Retighten.

Loose oil pump pulley or other pulley(s)

Retighten.

Looseness of linkage, play of steering, improper tightening 
(looseness) of suspension joint or steering column

Retighten or replace.

Sound generates from the inside of gearbox or oil pump.

Replace faulty parts in the gear-
box or oil pump.

Knocking
When turning steering wheel in 
both directions with small angle 
repeatedly at engine ON or 
OFF.

Excessive backlash
Loosened lock nut for adjusting backlash

Adjust and retighten.

Insufficient tightening or play in the tie-rod or tie-rod end

Retighten or replace.

Grinding noise (continuous)
While engine is running.

Air in vane pump

Inspect and retighten the fluid line 
connection.
Refill the fluid and vent air.

Vane pump seizing

Replace the oil pump.

Oil pump pulley bearing seized

Replace the oil pump.

Folded hose, flattened pipe

Replace.

Squeal, squeak (intermittent or 
continuous)
While engine is running.

Improper adjustment of pulley belt
Damaged or over tensioned pulley belt
Unequal length of pulley belts

Adjust or replace.
(Replace two belts as a set.)

Runout or dirty V-groove surface of oil pump pulley

Clean or replace.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Toyota 2016 RAV4 Quick Reference Manual preview
2016 RAV4
Бренд: Toyota Страницы: 56
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Бренд: Subaru Страницы: 34
Condor T-RAMP Quick Start Manual preview
T-RAMP
Бренд: Condor Страницы: 2
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Бренд: Xblitz Страницы: 30
Dodge Challenger 2013 Owner'S Manual preview
Challenger 2013
Бренд: Dodge Страницы: 543
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Бренд: FALCON RIDGE Страницы: 5
Alfa Romeo 1966 Spider 105 Faq preview
1966 Spider 105
Бренд: Alfa Romeo Страницы: 46
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Бренд: GARO Страницы: 15
ECS Electronics CT-050-B1 Fitting Instructions Manual preview
CT-050-B1
Бренд: ECS Electronics Страницы: 42
E&P HYDRAULICS Electronic Levelling System User Manual preview
Electronic Levelling System
Бренд: E&P HYDRAULICS Страницы: 6
Prorack K671 Fitting Instructions Manual preview
K671
Бренд: Prorack Страницы: 17
JVC KV-K1017 Installation & Connection Manual preview
KV-K1017
Бренд: JVC Страницы: 12
JVC KS-K6001 Installations preview
KS-K6001
Бренд: JVC Страницы: 12
JVC KV-K1015 Quick Start Manual preview
KV-K1015
Бренд: JVC Страницы: 4
Akyga AK-CH-07 User Manual preview
AK-CH-07
Бренд: Akyga Страницы: 4
Toyota PZ403-9963F-00 Fitting Instructions Manual preview
PZ403-9963F-00
Бренд: Toyota Страницы: 6
Crux SWRGM-49L Manual preview
SWRGM-49L
Бренд: Crux Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды