manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

AB(diag)-84

Diagnostic Chart with Trouble Code

AIRBAG SYSTEM (DIAGNOSTICS)

AE:DTC 72 PASSENGER’S AIRBAG FAILURE

DTC DETECTING CONDITION:

• Airbag main harness circuit is open, shorted or shorted to ground.
• Airbag module harness (Passenger’s side) circuit is open, shorted or shorted to ground.
• Passenger’s airbag module is faulty.
• Airbag control module is faulty.

CAUTION:
• Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground terminal from battery, and wait 20 seconds or more before starting to work.
• When replacing the airbag module, seat belt pretensioner, roll connector, control module and sen-
sor, reconnect each part and check that the warning light operates properly.
• When inspecting the airbag main harness, disconnect the airbag module connectors of the driver’s
and passenger’s seats for safety.
• When inspecting the airbag rear harness, disconnect the side airbag module connector, curtain
airbag module connector and seat belt pretensioner connector for safety reasons.

NOTE:
Prior to starting work, prepare two airbag resistors (98299PA040).

WIRING DIAGRAM:

Step

Check

Yes

No

1

CHECK POOR CONTACT OF CONNEC-
TORS.

Check for poor contact of the connectors 
between the airbag control module and the pas-
senger’s airbag module.

Is there poor contact?

Replace the airbag 
main harness 
along with body 
harness.

Go to step 

2

.

2

CHECK PASSENGER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect 
the ground cable from battery, and wait for 20 
seconds or more.
2) Remove the console front panel and discon-
nect the connectors (AB10) from (AB9).
3) Connect the connector (1P) in the test har-
ness P to connector (AB9).
4) Connect the airbag resistor to the connec-
tors (2P) and (3P) of test harness P.
5) Connect the battery ground terminal and 
turn the ignition switch to ON.

Does the airbag warning light 
illuminate for 6 seconds and go 
off?

Replace the pas-
senger’s airbag 
module. <Ref. to 
AB-16, Passen-
ger’s Airbag Mod-
ule.>

Go to step 

3

.

AB9

AB10

3

4

3

4

2

1

1

2

AB6

AB9

1 2 3 4

AB-02010

AIRBAG CONTROL MODULE

PASSENGER'S

AIRBAG MODULE

AB6

18 19 20

21 22 23 24 25 26 27 28

1 2 3 4

11 12 13 14

16 17

15

29 30

9

8

5 6 7

10

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Camcar 40052 Mounting Instructions preview
40052
Бренд: Camcar Страницы: 6
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Phonocar VM338 Mounting Instructions preview
VM338
Бренд: Phonocar Страницы: 6
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Бренд: Nav TV Страницы: 2
Kuda 182220 Installation Instruction preview
182220
Бренд: Kuda Страницы: 3
walser 30968 User Instructions preview
30968
Бренд: walser Страницы: 24
Dakota Digital MCL-7000 Series Quick Start Manual preview
MCL-7000 Series
Бренд: Dakota Digital Страницы: 2
Volvo 2010 C30 Owner'S Manual preview
2010 C30
Бренд: Volvo Страницы: 284
tams elektronik 54-01016 Manual preview
54-01016
Бренд: tams elektronik Страницы: 44
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Бренд: I.D. Systems Страницы: 41
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Бренд: Dodge Страницы: 444
Cadillac 2004 Seville Customer Convenience/Personalization Manual preview
2004 Seville
Бренд: Cadillac Страницы: 20
Pyle PLRD146 User Manual preview
PLRD146
Бренд: Pyle Страницы: 8
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Бренд: Jaeger Страницы: 16
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Бренд: Quadratec Страницы: 2
Oldsmobile ALERO 2001 Owner'S Manual preview
ALERO 2001
Бренд: Oldsmobile Страницы: 340
Chevrolet Chevelle 1965 Owner'S Manual preview
Chevelle 1965
Бренд: Chevrolet Страницы: 55

Бренды по названию

Популярные бренды

Загрузить еще бренды