manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

4AT(diag)-26

Diagnostic Procedure for Subaru Select Monitor Communication

AUTOMATIC TRANSMISSION (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK INSTALLATION OF TCM CONNEC-
TOR.

Turn the ignition switch to OFF.

Is TCM connector connected to 
TCM?

Go to step 

2

.

Connect the TCM 
connector to TCM.

2

CHECK SUBARU SELECT MONITOR POW-
ER SUPPLY CIRCUIT.

Measure the voltage between data link connec-
tor and chassis ground.

Connector & terminal

(B40) No. 16 (+) — Chassis ground (–):

Is the voltage 10 V or more?

Go to step 

3

.

Repair harness 
connector between 
the battery and 
data link connec-
tor, and poor con-
tact of the 
connector.

3

CHECK SUBARU SELECT MONITOR 
GROUND CIRCUIT.

1) Disconnect the connectors from ECM.
2) Measure the resistance of harness between 
data link connector and ECM.

Connector & terminal

(B40) No. 4 — (B136) No. 6:
(B40) No. 5 — (B136) No. 6:

Is the resistance less than 1 

:

? Go to step 

4

.

Repair the open 
circuit of harness 
between data link 
connector and 
ECM.

4

CHECK SUBARU SELECT MONITOR 
GROUND CIRCUIT.

Measure the resistance of harness between 
data link connector and chassis ground.

Connector & terminal

(B40) No. 16 — Chassis ground:

Is the resistance 1 M

:

 or 

more?

Go to step 

5

.

Repair the short 
circuit of harness 
between data link 
connector and 
ground terminals.

5

CHECK ENGINE GROUND CIRCUIT.

Check the engine ground circuit.

Is the engine ground circuit nor-
mal?

Go to step 

6

.

Repair ground cir-
cuit of ECM.

6

CHECK COMMUNICATION OF SUBARU SE-
LECT MONITOR.

1) Turn the ignition switch to ON.
2) Check communication with the transmis-
sion.

Is the name of system dis-
played on Subaru Select Moni-
tor?

Go to step 

11

.

Go to step 

7

.

7

CHECK COMMUNICATION OF SUBARU SE-
LECT MONITOR.

1) Turn the ignition switch to OFF.
2) Disconnect the connector from TCM.
3) Turn the ignition switch to ON.
4) Check communication with the engine sys-
tem.

Is the name of system dis-
played on Subaru Select Moni-
tor?

Go to step 

9

.

Go to step 

8

.

8

CHECK OUTPUT SIGNAL OF TCM.

1) Turn the ignition switch to OFF.
2) Connect the connector to TCM.
3) Disconnect the connectors from control 
modules connected to the data link connector 
(B40) No. 7, excluding TCM and ECM.

CAUTION:
When disconnecting the connector from air-
bag control module, always follow the pre-
cautions on AB section. <Ref. to AB-5,
CAUTION, General Description.>

4) Turn the ignition switch to ON.
5) Check communication with the transmission 
system.

Is the name of system dis-
played on Subaru Select Moni-
tor?

Check each control 
module.

Go to step 

9

.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Jeep Commander Overview Manual preview
Commander
Бренд: Jeep Страницы: 25
Jeep Commander Warranty Information Booklet preview
Commander
Бренд: Jeep Страницы: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Бренд: Farenheit Страницы: 8
NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Бренд: NavLinkz Страницы: 4
CITROEN PICASSO XSARA DESIRE 1.6 - MESUREMENT Manual preview
PICASSO XSARA DESIRE 1.6 - MESUREMENT
Бренд: CITROEN Страницы: 2
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
Atera 022 681 Manual preview
022 681
Бренд: Atera Страницы: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Бренд: RAM Страницы: 7
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Бренд: RAM Страницы: 76
Advantech TREK-550 Manual preview
TREK-550
Бренд: Advantech Страницы: 59
Chevrolet Impala Limited 2014 Owner'S Manual preview
Impala Limited 2014
Бренд: Chevrolet Страницы: 356
SCC Quik Grip Installation And Removal Instructions preview
Quik Grip
Бренд: SCC Страницы: 4
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Бренд: Mercedes-Benz Страницы: 296
JSPORT JSRLP024 Installation Instructions preview
JSRLP024
Бренд: JSPORT Страницы: 2
ADS FlashLogic FLC-FORS-FO1B-FLRSFO1-EN Install Manual preview
FlashLogic FLC-FORS-FO1B-FLRSFO1-EN
Бренд: ADS Страницы: 25
SAFARI SS18HF Manual preview
SS18HF
Бренд: SAFARI Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды