manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

DS-11

Propeller Shaft

DRIVE SHAFT SYSTEM

13) Install an extension cap to the transmission.

NOTE:
If extension cap is not available, place vinyl bag
over opening and fasten with string to prevent gear
oil or ATF from leaking.

B: INSTALLATION

1) Insert the sleeve yoke into the transmission and
attach center bearing to body.

Tightening torque:

52 N·m (5.3 kgf-m, 38.4 ft-lb)

2) Align the alignment marks and connect the
flange yoke and rear differential.

Tightening torque:

31 N·m (3.2 kgf-m, 22.9 ft-lb)

3) Install the heat shield cover.
4) Install the center exhaust pipe.
5) Install the rear exhaust pipe and muffler.

6) Lower the vehicle.
7) Connect the ground cable to battery.

C: INSPECTION

NOTE:
Do not disassemble propeller shaft. Check the fol-
lowing and replace if necessary.
• Dents or cracks on the tube surface
• Splines for deformation or abnormal wear
• Unsmooth joint operation or abnormal noise
• Center bearing for free play, noise or non-
smooth operation.
• Oil seals for abnormal wear or damage
• Damaged center bearing
Check the following points with propeller shaft in-
stalled in vehicle.

1. JOINTS AND CONNECTIONS

1) Remove the center exhaust pipe.
2) Remove the heat shield cover.
3) Check for any looseness of the yoke flange
mounting bolts which connect to the rear differen-
tial and center bearing bracket mounting bolts.

2. SPLINES AND BEARING

1) Remove the center exhaust pipe.
2) Remove the rear exhaust pipe and muffler.
3) Remove the heat shield cover.
4) Turn the propeller shaft by hand to see if abnor-
mal free play exists at splines. Also move yokes to
see if abnormal free play exists at spiders and
bearings.

(A) Extension cap

(A) Alignment mark

DS-00031

(A)

DS-00141

DS-00028

(A)

DS-00035

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Бренд: Kia Страницы: 10
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Trailboss QTHD519L Fitting Instructions Manual preview
QTHD519L
Бренд: Trailboss Страницы: 8
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Бренд: Zap Страницы: 16
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Бренд: Cadillac Страницы: 352
Blaupunkt 7 608 502 000 Installation Instructions Manual preview
7 608 502 000
Бренд: Blaupunkt Страницы: 6
Mitsubishi Outlander Plug-in hybrid Quick Manual preview
Outlander Plug-in hybrid
Бренд: Mitsubishi Страницы: 28
ADAPT SOLUTIONS ASENTO EV-COLC15R Installation Manual preview
ASENTO EV-COLC15R
Бренд: ADAPT SOLUTIONS Страницы: 22
Mercedes-Benz SLK 350 Brochure preview
SLK 350
Бренд: Mercedes-Benz Страницы: 24
AUTOTECH 10.297.300K-303K Installation Instructions preview
10.297.300K-303K
Бренд: AUTOTECH Страницы: 1
Kuda 050130 Installation Instruction preview
050130
Бренд: Kuda Страницы: 4
Gator ARV50T User Manual preview
ARV50T
Бренд: Gator Страницы: 18
Pet Gear PG9050TN Instruction Manual preview
PG9050TN
Бренд: Pet Gear Страницы: 4
TERAFLEX 1365000 Manual preview
1365000
Бренд: TERAFLEX Страницы: 18
Hyundai IONIQ HYBRID 2019 Quick Reference Manual preview
IONIQ HYBRID 2019
Бренд: Hyundai Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды