manualshive.com logo in svg

Subaru 2009 IMPREZA, Руководство по обслуживанию


Поделиться
Скачать
background image

5MT-81

General Diagnostic Table

MANUAL TRANSMISSION AND DIFFERENTIAL

2. DIFFERENTIAL

Symptoms

Possible cause

Corrective action

1. Broken differential (case, gear, bear-
ing, etc.)

NOTE:
Noise will occur, and eventually the differ-
ential will not be able to operate due to 
broken pieces obstructing the gear revo-
lution.

(a) Insufficient or improper oil

Disassemble the differential and replace 
broken components. At the same time 
check other components for any trouble, 
and replace if necessary.

(b) Use of vehicle under severe condi-
tions such as excessive load and 
improper use of the clutch

Readjust the preload and backlash of the 
bearing, and the contact surface of gear.

(c) Improper adjustment of taper roller 
bearing

Adjust.

(d) Improper adjustment of the drive pin-
ion and the hypoid driven gear

Adjust.

(e) Excessive backlash of a vehicle under 
severe operating conditions due to worn 
differential side gear, washer or differen-
tial pinion.

Add recommended oil to the specified 
level. Do not use vehicle under severe 
operating conditions.

(f) Loose hypoid driven gear tightening 
bolts

Tighten.

2. Differential and hypoid gear noises
Troubles of the differential and hypoid 
gear always appear as noise problems. 
Therefore noise is the first indication of 
trouble. However, noises from the engine, 
muffler, tire, exhaust gas, bearing, body, 
etc. are easily mistaken for the differential 
noise. Pay special attention to the hypoid 
gear noise because it is easily confused 
with other gear noises. There are the fol-
lowing four kinds of noises.
• Gear noise when driving:
If noise increases as the vehicle speed 
increases, it may be due to insufficient 
gear oil, incorrect gear engagement, 
damaged gears, etc.
• Gear noise when coasting:
Damaged gears due to misadjusted bear-
ings and incorrect shim adjustment.
• Bearing noise when driving or coasting:
Cracked, broken or damaged bearings
• Noise mainly when turning:
Noise from differential side gear, differen-
tial pinion or differential pinion shaft, etc.

(a) Insufficient oil

Lubricate.

(b) Improper adjustment of hypoid driven 
gear and drive pinion

Check the tooth contact.

(c) Worn teeth of hypoid driven gear and 
drive pinion

Replace as a set.
Readjust the bearing preload.

(d) Loose roller bearing

Readjust the backlash of the hypoid 
driven gear to drive pinion, and check the 
tooth contact.

(e) Distorted hypoid driven gear or differ-
ential case

Replace.

(f) Worn washer and differential pinion 
shaft

Replace.

Содержание 2009 IMPREZA




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2009 IMPREZA

cam 2850 Mounting Instructions preview
2850
Бренд: cam Страницы: 2
Dapper Lighting 575 Install Manual preview
575
Бренд: Dapper Lighting Страницы: 2
Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Бренд: Jeep Страницы: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Бренд: Jeep Страницы: 80
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Бренд: Jeep Страницы: 108
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Бренд: Mercedes-Benz Страницы: 388
Standby L54 Manual preview
L54
Бренд: Standby Страницы: 10
DEFA 412737 Fitting Instructions Manual preview
412737
Бренд: DEFA Страницы: 7
Prorack K869 Fitting Instructions Manual preview
K869
Бренд: Prorack Страницы: 15
ULTIMATE SPEED 94600 Assembly And Safety Advice preview
94600
Бренд: ULTIMATE SPEED Страницы: 21
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Бренд: Safe Fleet Страницы: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Бренд: Seat Страницы: 44
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Бренд: Ranger design Страницы: 24
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Бренд: Mynew Страницы: 5
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Бренд: Whispbar Страницы: 63
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды